338-06 load development

I've had good luck running H4350 as well in my 338-06. I've settled on 225 accubond's because the rifle just flat out shoots with them. I'll have to check the load but if I remember correctly it's around 2775 out of a 23" barrel and was .5 moa out to 300.
 
Shane Lindsey said:
Yupp. With five to confirm🤣

190gr HHT
60gr Varget
Norma 280 case
CCI 200
COAL 3.4"
C/D 2951, 2949, 2960, 2956, 2951
Avg 2953 FPS SD 4 ES 11 84 degrees
Click to expand...


IMG_5071.gif


If that's typical then the cost of the Hammer's isn't a factor, at least not compared to the ways I've been doing it…
 
Last edited:
Shane Lindsey said:
Yupp. With five to confirm🤣

190gr HHT
60gr Varget
Norma 280 case
CCI 200
COAL 3.4"
C/D 2951, 2949, 2960, 2956, 2951
Avg 2953 FPS SD 4 ES 11 84 degrees
Click to expand...
I'll definitely try that when my 338-06AI is complete. I will be using lapua brass though. Those are impressive speeds.

My record for load development with hammers was 7 rounds out of my 6.5x47 with the 124 HH. That includes getting it zeroed from my 130 AB load. Gotta like it when things work like that.
 
BEEMAN said:
I'll definitely try that when my 338-06AI is complete. I will be using lapua brass though. Those are impressive speeds.

My record for load development with hammers was 7 rounds out of my 6.5x47 with the 124 HH. That includes getting it zeroed from my 130 AB load. Gotta like it when things work like that.
Click to expand...

I should have stopped with the first three on this one, but wanted mo betta. But you can see the results above it just opened up. May have tightened back up, but brass was telling me no.
 
Equalizer said:
View attachment 602929

If that's typical then the cost of the Hammer's isn't a factor, at least not compared to the ways I've been doing it…
Click to expand...

The price of anything with 33 in it ain't cheap. This one isn't a plinker so it is ok.

Running them in a bigger case for steel…pass.

MAKE SURE YOUR TWIST RATE WORKS though. Over twist is better. Under and they'll hit like a hockey puck.
 
Equalizer said:
I couldn't find any of the 160 gr TTSX when I was getting components for this rifle. I bet they will really be moving from your AI!!!
Click to expand...
I tried the 160gr and 180gr TTSX they both shot really well. I just happen to have some of the 160's still. I was getting 3180 or so with the RL but not really pushing them hard. According to the book I should get close to the same with the 335.
 
Shane Lindsey said:
I should have stopped with the first three on this one, but wanted mo betta. But you can see the results above it just opened up. May have tightened back up, but brass was telling me no.
Click to expand...
I'll start low as I seen yours is a 338 Sherman. Kinda funny, as the gun that's getting a re barrel to 338-06AI was my 6.5 Sherman.
 
This evening I loaded up the same 20 cases, 5 each at the following charge weights:
56.1
56.4
56.7
57.0

Coal 3.34"

Hope to get them on target this weekend. I'm going to shoot them at 300 yards. Once this load is dialed in I'm gonna move to one of the other projectile options I have on hand. I did get on Hammer's website… I'm sure a few sample packs will find their way to my bench eventually… the 190 & 210 tipped HH look awesome!
 

Similar threads

J
30-06 Load Development
3 4 5
Replies
63
Views
27K
bob4
bob4
K
25-06 Load Development Problem
2 3
Replies
39
Views
16K
AussieWriter
A
D.Camilleri
338 Rum load development
Replies
12
Views
13K
D.Camilleri
D.Camilleri
PerrySBell
25-06 Load Development with H4831sc
2
Replies
26
Views
20K
Mike Matteson
M
B
load development for .338 lapua
Replies
5
Views
2K
Billfisher4evr
B

Recent Posts

Top