Not happy with my painting technique

Blacklab1

Well-Known Member
Joined
Feb 18, 2021
Messages
116
Location
Pa.
I'm trying to figure out how to do a decent camo paint job for my new rifle. I tried sponge painting and a Bob Ross approach with dabbing a round brush but I'm not really happy with either one. I'm trying to get close to something like a Manners sponge paint like the one I have a picture of but can't seem to get the bigger blotches. I tried trimming the natural sponge into different shapes but it's just not working out. I tried different pressures but if I press too hard it turns into a smudge and too light it's more like speckled. Any advice on how to get closer to a Manners?
 

Attachments

  • IMG_0397.jpeg
    IMG_0397.jpeg
    174.5 KB · Views: 452
  • IMG_0395.jpeg
    IMG_0395.jpeg
    144 KB · Views: 447
  • IMG_0398.jpeg
    IMG_0398.jpeg
    1 MB · Views: 447
Hello adk hunter and thanks for your thread a while back.
Here's the thread a picture of my first stock paint job.
I thought I would post some photos of my project.
First rifle I decided to do instead of getting dipped to make it my own.
I bought several cans or a green color and settled on Rust-oleum's green camo, dead flat clear and Montana can's Black marble effect.View attachment 478008View attachment 478009View attachment 478010View attachment 478011

I wasn't too concerned about getting the webbing perfectly to the very edge so taped past the exact edges. I did some practice passes on a box and went for it. I wanted it to be lightly done and was a little worried it would be rough or edgy. First pass was 95% and I gave a few light touch up shots around the grip and the top of the comb where I had it laying. Because it is so humid here I put in drying chamber🤣🤣
Wifey is in Italy! The dead flat clear coat didn't spray on so nicely but I did get it even. It did darken the green some.
Overall I learned a couple things but couldn't be happier.

Just wanted to share and encourage someone if you think this is difficult it isn't!
 

Attachments

  • 4B17065B-EC1C-4295-A8C1-148E10887E95.jpeg
    4B17065B-EC1C-4295-A8C1-148E10887E95.jpeg
    768.1 KB · Views: 173
By a large pour-us type sponge and tear it apart, (don't cut) tear the sponge and also pinch off small chunks to make it rough,
This is what your looking for. Spray paint some paper plates matte black for a practice canvas, Now you test out your patterns
 
Natural sponges.

Do a mock up of a stock with cardboard and use water to get the feel and right part of the sponge you prefer. I also spray the paint on cardboard and dip the sponge in it. Dab a few times to get the pressure and amount of paint on cardboard then go to the stock.
Exactly this.
Get the natural sponges from a craft store and soak them in water to soften them.
Pick out some different irregular shapes and sizes.
Practice on the cardboard first!
I added a clear coat after the sponge paint to protect it. Attached photo is before clear coat.
Good news is you can just paint that stock black and start again.
 

Attachments

  • IMG_7291.jpeg
    IMG_7291.jpeg
    441.2 KB · Views: 167
  • IMG_7292.jpeg
    IMG_7292.jpeg
    325.6 KB · Views: 168
  • IMG_7289.jpeg
    IMG_7289.jpeg
    473.3 KB · Views: 169
As noted, natural sponges from the craft store used in larger chunks.

If you use spray paint, I spray it into disposable bowls (the containers from veggies from the store) and use the paint from the bowl. It doesn't take long before that paint starts to dry and clump, and you need to use a different area of the sponge as well as a different area of the bowl.

Afterwards I used the webbing paint and clear.
 
Top