Your Ultimate 500 Yard Rig

[purpledragon]

My Remington 700 7 STW, never failed to get it done, had a DRT last season Whitetail at 720yds. Handloads with the 116gr GS Custom HV bullet and 82grs IMR 7828ssc

 

[Pbethell]

Again...It has to be the .280 Rem. Kevlar stock Mountain Rifle with a 3.5X10 Leupold VARI X III W/A.O. 7#12 OZ. Loaded. Easy pack at 8,000 ft. where most of my hunting is done. FYI I am well into my 60's years of age. No Problemo.

Ackley Improve this (280AI) and it is an ideal rig, IMO

 

[BUCKWORKMAN]

Would you take the chance of changing something that works well to an A.I. advantage ? This is where I have been pondering for years......Thank's...Buck.

 

[purpledragon]

One of my boys changed his 6mm/06 to the 6mm/06AI.....He'll tell ya.....BIG MISTAKE....brass life went to s**T

 

[Capt RB]

Would you take the chance of changing something that works well to an A.I. advantage ? This is where I have been pondering for years......Thank's...Buck.

The improving process improves the stability of the brass in every case. You also arrest some of the rearward movement of the rifle system with less bolt thrust at the same pressure. This allows you to gain speed and explore the next level of performance when you again reach the same pressure of the parent case. If you have a good barrel and decided you wanted to improve the case. If the work is done by a competent smith you will not lose what you had and most likely will see 100-200fps at the top end. The other end of it is you usually see slightly wider harmonic nodes due to the less bolt thrust and better headspace and chamber finish

 

[Good]

Yep, don't know what happened with purpledragon's boy's rig, but AI improves brass life.

 

[tomsd]

https://www.thetruthaboutguns.com/2...mpaign=wideopen&utm_content=[[rssitem_title]]

 

[tomsd]

https://www.thetruthaboutguns.com/2018/12/sam-hoober/best-308-rifle-for-beginners/?utm_source=wideopen&utm_medium=email&utm_campaign=wideopen&utm_content=[[rssitem_title]]

Six "entry level" .308's for beginners

 

[purpledragon]

His keeps splitting the necks for some reason....He'll get the fire form shot,and the next shot splits the neck. I'm no expert and can't give him any advise as to what his problem is, or where....

 

[purpledragon]

Oh, he is using new neck sized 25-06 brass I think it's R-P brass....

 

[MudRunner2005]

His keeps splitting the necks for some reason....He'll get the fire form shot,and the next shot splits the neck. I'm no expert and can't give him any advise as to what his problem is, or where....

Tell him to run book starting loads that have been reduced by 5% to 10%, for fire-forming. He does not need to run high-pressure loads for fire-forming brass. That weakens the necks and shoulders, and sometimes causes them to split while fire-forming. This could be his issue.

Lots of bad advice out there for fire-forming for wildcats and AI cartridges, and I've heard that BS line of "run hot loads while fire-forming" quite a bit. It causes LOTS of problems.

 

[purpledragon]

Thank you for the advice...But even the cases he fire forms with the Cream Of Wheat do the same thing.....

 

[Danehunter]

6.5 CM BROWNING X-BOLT PRO SIGHT-IN RESULTS:

Today I sighted in my new 6.5 CM X-Bolt Pro and the last 3 on X-ring zeroing shots were a true 1/2 MOA. This was shooting off my range bag B/C I forgot my **** cast iron front rest. (140 gr Hornady ELD-M ammo, SWFA SS 3 - 15 x 42, FFP, mil/mil scope)

THEN I went to our club's steel range and shot (again, off my range bag) to 547 yards (sillhouette & gongs) hitting every shot but one from 212 yard chickens to 370 yard pigs to the 547 yard sheep and gongs. That rifle and SWFA SS 3 - 15 x 42 scope combo is very accurate. Happy shooter here!

Eric B.

 

[Saracen]

Going to have to be 300 win mag.
I'm all about being over prepared and then just go with the flow.

I got one years ago, shoot everything with it, and never looked back.