Typical Range day setup. Pictures please!

Typical setup for me from the bench for load development. Range bag not pictured.

Will get off the bench on the tripod or bipod for steel work at 300-600.

1000005107.jpg
1000004022.jpg
1000005657.jpg
 
Caldwell makes a decent front rest. Atlas makes a very nice front Bi Pod, while Harris seems to turn my rifle into a po go stick in how it bounces the rifle around, ok for field work, but not for tiny group shooting.

Rear bag, fill with HEAVY sand, you will NEVER regret the choice.
 
Last edited:
I either use an atlas bipod or Caldwell bag (remember to remove your front sling stud) and lately I've been using a Triad tactical rear bag. I've probably tried a dozen different rear bags and this one has been used the most.

I don't have any pictures and not sure why haha.
 
My set up for sporters is pretty well identical to this, my front rest is an older version of the "Rock". For the rifles with flat bottom forends I use an SEB Mini-X front rest. I use Protector sandbags, front and rear and I order them prefilled with heavy sand. I want a Garmin!
It's unbelievable how "attached" you get to the Garmin. I would never even consider leaving it or if I did by accident I would turn around and go home. Just as important as having the ammo with you, lol.
 
I would invest in higher quality rests if I had easy access to a range. I typically just use a decent bipod (Atlas or Harris) and cheaper rear bags when doing load development. I realize that chasing tiny groups could be improved, if I paid more attention to my setup. However, I already need to figure out a better way to transport all my stuff to a range day. Multiple trips to the truck carrying heavy gear takes some of the joy out of a day at the range for me.
I bought a collapsable wagon cart for under $100 that works great. Fits behind my seat on the floor. Now it takes me one trip.
 

Attachments

  • IMG_6632.jpeg
    IMG_6632.jpeg
    329.2 KB · Views: 5
Lately it's been Caldwell Tack Driver bags, a small and large one, with homemade denim sand bags on top to nestle the rifle into. I have a cheap plastic adjustable tripod that I've used occasionally hoping it will be useful but....maybe one of the heavier cast iron ones would be better. Typically just on sandbags.
 
About 30 or 40 years ago, I made my bags from blue jean legs……stitch across one end, fill bag with sand, stitch closed.

I don't shot nearly as much as many of you, but with a little care mine have lasted quite well.

I use an "elcheapo" adjustable front rest, and leather "rabbit ear" type rear. I put bags beneath the rear "rabbit ear" bag as needed for proper height. For rear height "fine tuning" I merely pinch the sand bag for height increase or nestle the rifle a bit deeper into the bag to lower.

If it's already perfectly clear……this is the "poor boy - red neck" setup! 😉 But, it seems to work for me!

Addendum: I also use a volley ball elbow pad on the bench arm, I found out the hard way that after a few shots…..a lot of skin was left on the bench after firing a few rounds. The burning pain is rather distracting! 😜 memtb
I use one of those foam knee pads you use in gardening for an elbow rest only a couple busks after winter hits
 
I use one of those foam knee pads you use in gardening for an elbow rest only a couple busks after winter hits

I've always covered the plywood top of my bench with a towel, but the combination of the top's aging and a heavy recoil rifle, the towel wasn't nearly enough! 😜 memtb
 
I usually use either a Harris or Atlas bipod up front and a LRO Wedge with heavy fill at the rear. That is a rock solid setup but the bag is heavy. Lately I have been using a Phoenix Shooting Bags medium Ridge Runner at the rear since that is what I will be carrying in the field this year.
 
Top