Only a 25x45 sharps in an ar15. It was pretty uneventful with a lighter bullet and not a ton of speed.
-
If you are being asked to change your password, and unsure how to do it, follow these instructions. Click here
The .257 -WHICH CARTRIDGE???
- Thread starter Coyote Shadow Tracker
- Start date
Help Support Long Range Hunting Forum
sierracharlie338
Well-Known Member
Love my 25X45 its a hammer on Texas WTs.
What powder and bullet weight do you use with your 25-284?
What powder and bullet weight did you use with your 25-284?
What powder do you use with your 25-284 and the 133's?
VLD Pilot
Well-Known Member
RL26
Thank you sir.
If you are comfortable sharing the information, what was your load?
You could message the info as well.
I am not going to jump to your load when I start
VLD Pilot
Well-Known Member
No I have zero issues sharing with all. Just recommend starting lower. Mine isn't hot really either. No bolt lift issues, no case marks or damage. Fairly warm I'd say. My freebore is liberal keeping pressure down a bit. I know it reduces barrel life but there cheap enough. I really only care to run the 131-135s around 3000-3100 anyway. I think the best accuracy will be around 3K in the end. 54.3-54.7 grains got me decent groups at around 3200. Roughly .010 off. Last two shots on my Chrono.Thank you sir.
If you are comfortable sharing the information, what was your load?
You could message the info as well.
I am not going to jump to your load when I start
Attachments
Thanks!
VLD Pilot
Well-Known Member
This was around 2950 and my best groups. 3 shots. Felt it was a little slow so went to 54.0 grains and still had good groups but opened up to around .3. At 3200 they were around .5". I think with some seating changes and fine tuning powder charges, I can wind up with .25" and around 3050-3100.
Attachments
willfrye027
Well-Known Member
135gr Berger's. H1000, RL23, n566 and RL26 all seemed to work. H1000 was stupid accurate and cleaner burning for me. It would probably work with any of the slow burning magnum powders.
I also use R26 in my 25-284. But I'm shooting the 131 BJ. 3150 FPS out of a 25" Carbon Helix6 with a 1-7.25" twist.
Nix the short action, planned failure with those long VLD Bullets. I have been down the road of a 25/284 and 6/284 on two different Rem 700 short actions, NEVER NEVER again!
For the easy button, a std 25/06 with R#26 should impress all, and go AI for impressing. Lapua 30/06 brass is floating around for the Win. AI brass made from Winchester 270 brass is very good.
If you want more, then go 257 Weatherby, custom reamer with freebore to match the 133. I have a reamer on file with PTG for just necking down Winchester brand of 264 WM & 7 Rem mag brass to the 257 Weatherby with a .060 shorter neck.
Exotic stuff in this day and age, with shortages of everything including long waits and impossible to get in many component choices, demands some level-headed thinking/planning.
For the easy button, a std 25/06 with R#26 should impress all, and go AI for impressing. Lapua 30/06 brass is floating around for the Win. AI brass made from Winchester 270 brass is very good.
If you want more, then go 257 Weatherby, custom reamer with freebore to match the 133. I have a reamer on file with PTG for just necking down Winchester brand of 264 WM & 7 Rem mag brass to the 257 Weatherby with a .060 shorter neck.
Exotic stuff in this day and age, with shortages of everything including long waits and impossible to get in many component choices, demands some level-headed thinking/planning.
Last edited:
Surprised that nobody has come up with a 25/300PRC, It'd be like a 22-250 on steroids!!! Might be too overbore???
