OK, glad I wasn't drinking coffee while reading these! Then again a coffee flush thru the nose is probably good hygiene!
Help Support Long Range Hunting Forum
100percent
Well-Known Member
Danehunter
Well-Known Member
MPAYNE,
A "Deal on TP"?? It is no longer referred to as TP. It is now called "ButtCoin".
Eric B.
A "Deal on TP"?? It is no longer referred to as TP. It is now called "ButtCoin".
Eric B.
D
Deleted member 103481
Guest
Razor lht is here and installed with a ARC m10 extra low rings... ocular bell has more than adequate space... however when running the bolt it has enough play to hit the eye bell of the scope when lifted up. So, not sure where to go from here, it's only at the top of its play that it hits. May have to go to slightly higher seekins rings, even though I do not want to. They next highest ARC rings(lows) are 0.94 and don't want to go that high.
edit* seekins 0.87" are perfect
Last edited by a moderator:
mpayne
Well-Known Member
I would leave it low and have the bolt handle worked on.
D
Deleted member 103481
Guest
considering this as well, I just spoke with defiance and they have had a few people say they had this issue on hunting rigs and apparently are looking at making some handles that are turned down more in the middle. Unfortunately their production appears to be shut down during the pandemic so not sure when that would actually happen.
mpayne
Well-Known Member
It's just too sweet of a rig to take a saw all to
D
Deleted member 103481
Guest
I have taken a dremel to more than one firearm, but this one won'tget that treatment! I will try the seekins .87 and see if the extra 3 hundredths clears it and go from there. Doesn't hurt that they are cheaper than the m10s!It's just too sweet of a rig to take a saw all to
Last edited by a moderator:
D
Deleted member 103481
Guest
Sweet, Better when you get it parked next to some success
VERY true
Don A Parsons
Well-Known Member
That is 1 nice,,, no,,, awesome looking rifle...
Who would no like a mix of cold iron and real wood...
It makes my rig look sick,,, Ha
photos.app.goo.gl
Same here with this barrel,,, a 2.8 contour which is 1mm thicker then a factory Remington sporter barrel,,, total weight of this hunting rifle is 11.9 lbs with ammo,,, optic,,, bypod,,, sling and ammo pouch of 9 extra shots...
Yes,,, the little bit of thicker pipe allows for some fairly consistent shots back to back...
Any-Who,,, it aint nothing like the package you have on the go,,, thx for sharing...
Don
Who would no like a mix of cold iron and real wood...
It makes my rig look sick,,, Ha
New item by Don Parsons
photos.app.goo.gl
Same here with this barrel,,, a 2.8 contour which is 1mm thicker then a factory Remington sporter barrel,,, total weight of this hunting rifle is 11.9 lbs with ammo,,, optic,,, bypod,,, sling and ammo pouch of 9 extra shots...
Yes,,, the little bit of thicker pipe allows for some fairly consistent shots back to back...
Any-Who,,, it aint nothing like the package you have on the go,,, thx for sharing...
Don
D
Deleted member 103481
Guest
No issues with seekins 0.87" rings, so we are back in business, even better this ring height is perfect for off hand shooting. This rifle shoulders phenomenally. Now to getting some powder through it!
loaded 75 and 75.5 grains of rl26 at 3.720 coal for an initial range trip. I don't think I will have any pressure issues with that load but I'd like to not waste a bunch of time in the reloading room. Things are moving along!
loaded 75 and 75.5 grains of rl26 at 3.720 coal for an initial range trip. I don't think I will have any pressure issues with that load but I'd like to not waste a bunch of time in the reloading room. Things are moving along!
