haftime
Well-Known Member
Carbon wrapped barrel, 300 RUM with a Ti can, fingers crossed. Did you see signs of pressure? I know I'm already on that jagged line.
Do silencers change a rifle's preferred load?
- Thread starter haftime
- Start date
Help Support Long Range Hunting Forum
med358-boise
Well-Known Member
I looked at this issue a different way:
1) Will I ever buy a new rifle?
2) Will I ever try new bullets?
if the answer to either of those is "yes", then I am going to do load development anyway. Therefore, adding a suppressor is really no different than buying a new rifle or trying new bullets.
Personally, I first start with powders and bullets that have a very good reputations for accuracy and research to see if there are "known good loads" for my cartridge. After that, I use the Optimal Charge Weight Method for load development. Using the preceding approach, I can have the load developed, confirmed, and the rifle zeroed in three range sessions or four at the most.
Granted, I don't shoot beyond 600 yards and I am satisfied with a sub .8 MOA group. I also don't worry about 100 fps in a velocity.
Sorry for the somewhat long winded and slightly off-topic answer, but many "challenges" in life can be mitigated by viewing the issue in a different light; i.e., don't worry so much about load development; embrace and improve your load development process.
1) Will I ever buy a new rifle?
2) Will I ever try new bullets?
if the answer to either of those is "yes", then I am going to do load development anyway. Therefore, adding a suppressor is really no different than buying a new rifle or trying new bullets.
Personally, I first start with powders and bullets that have a very good reputations for accuracy and research to see if there are "known good loads" for my cartridge. After that, I use the Optimal Charge Weight Method for load development. Using the preceding approach, I can have the load developed, confirmed, and the rifle zeroed in three range sessions or four at the most.
Granted, I don't shoot beyond 600 yards and I am satisfied with a sub .8 MOA group. I also don't worry about 100 fps in a velocity.
Sorry for the somewhat long winded and slightly off-topic answer, but many "challenges" in life can be mitigated by viewing the issue in a different light; i.e., don't worry so much about load development; embrace and improve your load development process.
Last edited:
Splitt
Active Member
I can only speak to my own experiences, of course.
Bought my first can (30 cal) two years ago (1 year wait sucked). I have used it on a 300BO AR and my .308. I've learned two things. First being is that my POI shifted 9 MOA when I pulled the break and put the can on my Savage 10. Second being is that it's like driving a really nice truck. Once you have used it, you won't want to go back.
If you decide to use it on your bolt system, use direct thread and just leave it after you do your load development. It's just easier in the long run. Direct thread will keep your position of the suppressor the same (more or less) every time you take it on and off for cleaning. I wanted to go this crazy route of buying muzzle devices that would make swapping between the two rifles easier, but my POI would shift every time I took them on and off, and not a little bit. It was a hard lesson to learn after a couple hundred dollars later. DT is also better because they like to loosen after several shots. Check it frequently. I also bought a pair of high temp grill gloves with silicone grips and a rubber belt wrench to tighten/remove it. Carbon buildup can make it difficult to remove. Depending on the material, they take a fair time to cool down.
You'll buy more, don't you worry. It's nearly as addictive as buying firearms itself. I have three now. The .22LR one is laughably quiet on the 10/22 and the pistol (sr22). Bought my first big boy pistol can (.45 cal) this summer. Now I'm considering buying another 30cal or maybe one that will cover up to .338 should I decide to get one. The $200 "could I have this daddy" tax is a pain and they are still pricy as hell, but I think of all the accessories I've bought for my rifles, this one is the most beneficial one I've ever used.
Sorry for the word salad and do enjoy suppressor use!
Helpful links:
pewscience.com
Plug in your rifle info and go…
Subsonic load data from Hodgdon. I haven't played with it yet, so take that with a grain of salt.
Bought my first can (30 cal) two years ago (1 year wait sucked). I have used it on a 300BO AR and my .308. I've learned two things. First being is that my POI shifted 9 MOA when I pulled the break and put the can on my Savage 10. Second being is that it's like driving a really nice truck. Once you have used it, you won't want to go back.
If you decide to use it on your bolt system, use direct thread and just leave it after you do your load development. It's just easier in the long run. Direct thread will keep your position of the suppressor the same (more or less) every time you take it on and off for cleaning. I wanted to go this crazy route of buying muzzle devices that would make swapping between the two rifles easier, but my POI would shift every time I took them on and off, and not a little bit. It was a hard lesson to learn after a couple hundred dollars later. DT is also better because they like to loosen after several shots. Check it frequently. I also bought a pair of high temp grill gloves with silicone grips and a rubber belt wrench to tighten/remove it. Carbon buildup can make it difficult to remove. Depending on the material, they take a fair time to cool down.
You'll buy more, don't you worry. It's nearly as addictive as buying firearms itself. I have three now. The .22LR one is laughably quiet on the 10/22 and the pistol (sr22). Bought my first big boy pistol can (.45 cal) this summer. Now I'm considering buying another 30cal or maybe one that will cover up to .338 should I decide to get one. The $200 "could I have this daddy" tax is a pain and they are still pricy as hell, but I think of all the accessories I've bought for my rifles, this one is the most beneficial one I've ever used.
Sorry for the word salad and do enjoy suppressor use!
Helpful links:
Suppressor Sound Rankings — PEW Science
What is the quietest silencer for your suppressed firearm? The quietest suppressor for your use case is listed on this page with detailed links to the Silencer Sound Standard test data. PEW Science test data with PEW-SOFT is the most accurate suppressor test data available.
pewscience.com
Subsonic load data from Hodgdon. I haven't played with it yet, so take that with a grain of salt.
Last edited:
Ballistic High Speed did a video on this topic, sort of. The visual of a bullet exiting a barrel @ 200,000 and 600,00 fps. Some rounds clearly get a little push from the expanding gas cloud as and/or after it exits the barrel. The suppressed rounds are significantly different. His reaction at the ends of shooting some of the firearms is pretty funny.
keith4kk
Active Member
I just placed a supressor on our 8th rifle. 2 are gas, 6 are bolt. 556, 6mmCreed, 22250, 300wm, 300wsm, 270, 308. All the bolts I handload except 6mm, just not there yet. I first added ASR brakes to them all then adjusted the load to account for the change. Usually within a grain, not a lot of change there. Then we added the suppressors. All had a POI change, usually within 2.5 inches and mostly elevation. None of the loads were affected by the supressor. 4 have been to 1000+ before and after the supressor with the same loads. I just purchased a 22 supressor yesterday, can't wait to get it shooting.
"Long's theory" is legit imho. In the RF world we call that SWR aka Standing Wave Ratio. It's the ratio of transmitted power vs reflected power. It's a deep subject that I won't claim to fully understand. Physics is physics... the waves that form and travel down the barrel reaches the end and does what? It reflects back and interferes unless the timing of the wave is in the Goldilocks zone (just right).
From the PDF
From the PDF
I run tuners and tuner/Brakes on several barrels. Very, very small adjustments not only changes the group size, but the impact. I have barrels that once a brake is installed, the barrel does not want to shoot well(5/8"), and vise a versa. This is a humbling sport.
You are spot on.
It's a fact of physics that the gas being discharged from the barrel once the projectile leaves the pipe is traveling and expanding much faster than the bullets flight. This is exacerbated by the "hose nozzle" effect of boat tail bullets allowing gas to pass the bullet before the base even clears the muzzle.
Essentially, a bullet has to fly through its own prop wash of expanding and igniting gasses in the first couple feet of flight. I believe this is why we often see videos of projectile yaw during that first few feet too. With a suppressor, those gasses are peeled off as the bullet goes through the baffles in the can, making for a much cleaner exit and exponentially less external forces on the bullet.
Essentially, a bullet has to fly through its own prop wash of expanding and igniting gasses in the first couple feet of flight. I believe this is why we often see videos of projectile yaw during that first few feet too. With a suppressor, those gasses are peeled off as the bullet goes through the baffles in the can, making for a much cleaner exit and exponentially less external forces on the bullet.
I have experience the same with my 6.5 Creed 6.5 PRC. I haven't seen any accuracy problems what so ever.
Attachments
This is one of the best videos of a suppressor.
Stop that you make to much sense, can't have that here!
The clear suppressor vid is eye opening.
SED is my favorite YouTube channel. The supersonic baseball cannon is freaking AWESOME!
SED is my favorite YouTube channel. The supersonic baseball cannon is freaking AWESOME!
