Absolute Hammer load data

Yes I have. It was around 3240 fps but the more accurate node was 100fps slower. I believe I was using H4831. Can't remember if it was that or RL23, but I'm pretty sure it was H4831.
Thanks. I'm getting the exact same velocity out of mine with the 124's ahead of 52.5 gr H100V, Lapua brass, Fed 210, OAL 3.088" in a 26" CA Classic...
 

Attachments

  • CA 6.5x284-124 HH.jpeg
    CA 6.5x284-124 HH.jpeg
    898.5 KB · Views: 107
.243 Win.
Dogtown brass full prep
cci-34 primer
Varget@ 45.7
69 absolute hammer
2.685 C.O.A.L with a Butterbean crimp
5 shot chrono average 3791fps with a 6 E.S
24 inch Shilen SM heavy sporter with 44 down the tube
BUGHOLES for 3 three shot groups at 100
action is a Savage tactical bedded in a, Boyds at one stock, Northland nut and lug trigger at one pound
found pressure at 47 grains 3876 fps barrel should speed up in the next 30 to 50 rounds I suspect
 
Last edited:
Got to test some of the N560 with the 123gr AH and I think I might have found a new powder to run with for deer season.

24" Proof Prefit - Dead Air Nomad L
6.5 PRC
Lapua Brass
Fed 210M
N560
1/8th turn FCD
2.937 COAL

61.6 - 3294
61.9 - 3298
62.2 - 3318
62.5 - 3344
62.8 - 3377
63.1 - 3374 - Ejector and Sight bolt
63.4 - 3402 - Ejector and heavy bolt

Looks like I'm going to load 62.8 and roll with it as N560 seems to pick up about 90 fps with less pressure over the IMR 4955 loads I was planning to use.
 
Had some time to finish up fireforming some 6.5 Max Brass today.

Cartridge: 6.5 Sherman Max
Absolute: 123g
Barrel; Bartlein 20" #4 Carbon Wrap
Mod 400bb SS 1-7.5 twist
Brass: Sherman ADG, .003nk ten, 1/8 crimp.
Primer: Fed 210m
COAL: 2.98
Powder: Re-26
Charge: 64gr
Velocity: 3250 average
Notes: Barrel Break in / Fireforming load
Suppressor, ** shot nice tight groups**

Now going to load up a ladder with 110 Hammer Hunters & Re-16.

Thanks to GL, Lejuch, BB, Rich, & Steve,
as well as others who contributed info. 👍
 
Your H100V loads are almost spot on for me with ADG brass except I was getting 3400 at 58.2gr from a 24". When I do my part the groups are great at the higher speed.View attachment 259278View attachment 259279

Also I did the test from 51 to 59.5gr of IMR 4955 and the entire group was right at 2 MOA, take out the two lowest and two highest and you have from 52 to 58.9 producing a group slightly over one MOA for 16 shots.

View attachment 259280View attachment 259281
Do you have speeds or pressure symptom notes for this run? Can you number which holes were what shots?
 
Do you have speeds or pressure symptom notes for this run? Can you number which holes were what shots?

I stopped at 59.5 as it was max pressure with very heavy bolt lift and ejector marks, I believe light ejector marks started at 58.6 if I remember correctly. Below is the velocity chart from my excel notes, also note that two other rifles maxed at 58.6gr showing the same pressure signs as my rifle did at 59.5gr.

1637545452049.png


I've since switched the barrel to a different action which shows pressure earlier and am now running VV N560. My N560 load should give me around 3370fps, range was to busy for the LabRadar today but I did check my zero for the opening of deer season next week. There's three in there but I'm not sure which hole it went through so I just used the two for group sizing.

BAA6196F-2BA6-464E-BB91-79A00AD5BF1D.jpeg
 
Very faint ejector @ 57.5, I think I can push a little more, but I'm about out of room. The only thing I have faster is IMR 4064 and that will be too fast, won't it? 20" rem factory barrel btw.
 

Attachments

  • EB890FF8-5973-4F7E-8433-EE91864D541A.jpeg
    EB890FF8-5973-4F7E-8433-EE91864D541A.jpeg
    1.4 MB · Views: 101

Recent Posts

Top