12ga,10ga,8ga,4ga FH;585HE/700HE, other Big Bores--

Here is picture of 100 cases loaded with CEB solid nose bullets
and hollowpoints. This bullet is a turned solid with wide meplat
or wide hollowpoint. .

100ceb.jpg


Here is picture of triball loads that fellows like for deer and hogs,
and just general tear em up fun, with using BPGS seal to improve
sealing under what are heavier loads. The balls are .600" and
315gr. each. The wadcup is a TUPRW123 that Precision sells.

triball.jpg



Our 585 caliber is modern bolt action continuance of the 577 Nitro
Express rimmed case, that many big game hunters like, usually
set up in double rifles. It has an interesting history, from the old 24ga
size to 577NE, to 585 Nyati with G&A picture of Ross Seyfreid
shooting one in a Ruger #1 under recoil knocking his shooting glasses
off, to the Trex of internet fame knocking guys over with recoil,
to our 585HE the strongest yet.

The 577NE is an offshoot of 24 gauge caliber paper cases, only they went
eventially to brass cases. Back in the 1860-70s, starting first with short
cases and black powder, cases built like shotgun cases, called the
577 Snider, then going to coiled brass cases, still with black powder,
then on to drawn brass cases, called 577 BP Express. then to 3"
and other longer cases with smokeless. The Snider started out with a bullet
of .570" diameter and through the progression to the 577NE bullet
diameter ended up at .585". This general bore diameter of cartridge guns
and muzzle loaders, it is really interesting on how they developed
and were used by military and then hunters over the years. The Snider
was necked down to make the 577-450 , a military round used all
over the British Empire, by the tens of millions.

Bases of both 24ga and 577NE are about the same. Now we have made a
24ga FH, a slight regression to earlier times, by taking 577NE brass, and
reducing rim diameter to 24ga specs. Two minute job. And
stamp the caseheads 24 ga.

For shotgun upgrading in power and range, It is all about increasing
the power in easy to find brass cases, stronger actions, and finding
reasonable price rifled barrels. Same barrels we found for 585, work for 24ga.
The 577NE brass we make 24ga drawn cases from, for example are
about a third the cost of 600NE brass, or getting turned 24ga cases made.
We could use 24ga thin cases but they are a pain, expand way too much,
with slug loads which makes resizing without crumpling cases a problem.

Info about the power in types of guns normally set up with 24ga FH,
break actions, bolt shotguns,etc. In thin brass 24ga case, 440gr slug
goes 1500, with about 2000 ft lbs, that's in a 2.5" Magtech brass case.
Now using the better, heavier 3" brass we got, we can increase speed
to 1750 fps increasing energy 50%, going to 2000 fps about doubles
energy. And going to 2300 which good brass holds ok, in heavy barrel
gun, gets us near 2 1/2 times the energy. About 37-40,000 psi which the
actions hold in this smaller diameter case, compared to 12 gauge size.
So makes relatively smaller bore shotgun, 24ga, with 458WIN power.
.Perfect with Minie bullets. Perfect for deer and hogs, bear, etc.

Great for slug hunting in shotgun only areas. We mark barrels 24ga
and cases 24. A decent case that is complimentary to our 585HE....Ed
 
Guys asking about using 585 CEB bullet in our 12ga super
sabot. Here is picture, We just took off the bottom band and couple
middle bands on the CEB and it fit perfect in our 12ga sabot,
which uses .575" slugs. Hollowpoint one pictured 700gr in the
sabot loaded in brass case. Can be used in plastic case with a
special made hollowed out long roll crimper.

cebsabot.jpg


Getting some more interest in our 585HE.
An application for our 585 HE is for guys with old military 14.5mm
PTRDs, to use our case with chamber insert. In many places 14.5
cases are scarce, real expensive, as well as most 14.5mm cases
being steel are not the easiest to resize/reload. Our case sizes
like regular cases and can be easily reloaded many times.

And a PTRD with almost a 5 foot long barrel could get 650gr
spitzer bullet to about same speed the 14.5mm gets a 900 gr using
3 times as much powder. About 3300 fps. Or get a 900gr at 2800.
Great possibilities for fun shooting. For tactical use in a place
where it would be useful to reload in the operations field, where
steel cases are scarce. 100 of our cases do over 2000 reloads.

585-14,5mm.jpg


I like Enfields to put our 585HEs in, for reasonable cost guns, the
actions once sporterized are one of the longest for long cases. .
Here is inexpensive way to fancy up the Enfield Bolt handle by
cutting the dogleg part of the old handle off and welding on
inexpensive contoured handles I found, one of which is like
Ruger 77 handle, the one on the right . Something even a novice
like me can do.....

enhandle.jpg


A lot of guys are crazy about CEB bullets. Here are light 450gr
ones in our 24ga FH. That hollowpoint can range in weight 450gr
to 700gr depending on how much we cut off the back..
The 24ga FH brass case is nice complement to our 585HE,
for shotgun only deer hunters that want a .585" caliber,
and easy to find big bore bullets.... Ed

24liteceb.jpg
 
For lightweight plinking, deer hunting, etc, in 585HE as well as 24ga FH
here is picture of 58cal Hornady sabot that holds .451/.452" light
bullets 225 to 300 gr. A way to shoot targets economically. Low recoil
but a big bang and satisfaction. A 250 gr bullet would go about
mach 4 with a top load..

58hornadyjkt.jpg


Here is what 585 bull barrel, target blank looks like, 1 5/8" OD and 32" long.
It'll go in heavy action of some kind. 4th one from the left. The one in yellow
sleave on top, is a heavy contoured one with muzzle of .980". we got a
bunch of them and so does McGowen.

585bull.jpg



Here is picture, nice cast bullet I like for the 585HE and 24ga FH.
It is .585" diameter and 650 gr and these particular ones are a
hard lead alloy, plus they've been heatreated. They are about as
hard as copper jacketed softs pivtured. These in .575'' size would
work in our 12ga sabot..

585castbul.jpg


But to penetrate good and do great damage to game or target they
can be fairly soft lead and hollowbase like Minie Bullets. Here is picture
of timber drilled through with .585 soft lead Minie from 585HE.
Picture is the back of 6x6 timbers where Minie bullets came out.

58calpen.jpg


Guys experimenting with multiple ball loads in 12ga wadcups, here is a
way to keep them together group wise.Ed


screwball.jpg
 
Here is picture of our NEF 12ga FH with Hogue Compstock. It has the
recoiling cam and springs in the hollow butt plus some weght,

compstock12.jpg


Here is a variety of slugs and bullets that fit in the 12ga dangerous
game slug, lock on sabot. BPI sells that DG slug.

.
dgslugs.jpg


There is couple 585 videos on Swann Gunsmithing's Facebook site;
Of our 585HE in first Ruger #1, that was done in Australia.It was set up
for the poster Tankhunter on the AR big bore forums. That gun killed the
first AUS buff, killed by a 585HE, that I posted picture of above. You can
go direct to the page and click on the videos to watch the test firings..

https://www.facebook.com/swanbarrels/videos


Here is picture our 585HE in a Montana PH action in a MPI stock, with the
style of a CZ stock and metal will be finished with a Gun Kote finish.


ph585jm.jpg



Here is picture of a 585HE we did in a Mauser 98 as a
singleshot test gun. We used a composite stock we
adapted to fit action. Weighted to 12 lbs.
Enfield in back, you can see it is longer.

mau585he.jpg


And speaking of singleshots a fellow in the Yukon is
just finishing up one in a Ruger #1.And the 24hr Campfire
forum has over a million views of this thread, ..ED
 
The 12ga FH isn't the first wildcat case built on BMG brass, it was preceded by
target rounds like the necked down 338 Talbot, the cut off 700 DKT for big game,
necked down to .416 and . 458, and more, but the following one was way
before them, in my favorite rifle caliber, for .585" bullets.

One of first modern era 585 caliber wildcats, since WW2, the 575 Miller-Greiss Magnum,
was first mentioned in the fifties, It was made from BMG brass shortened to 2.70" long
and necked up from 50 cal to .585". But actually if cut off first, it would be annealed, necked
down to hold 585 bullet. Fairly sharp shoulder.

They rebated the rim quite a ways down to .618" to maybe fit 98 Mauser bolt.
Maybe used a special hogged out, reworked action. Listed as
shooting 750gr bullet about 2400 fps. It holds about 150gr of ball powder under
a 750 gr bullet, maybe little less than 3" 50cal spotter case, where our 585HE holds
180gr under a 750gr'.

We made one for experimenting on a full length BMG case.With rim left same as the base
and would need a BMG or PH sized bolt and action. I'm glad to be a big bore wildcatter,
and happy to be in the company of big bore nuts, old and new. Years ago when guys did
big wildcats on BMGs, they took what was available, full length BMGs to rework, and but
maybe back then they could have used the 3" BMG spotter case, by shortening the neck,
if they could have found couple barrels full.

But it takes a lot of work to reform and shorten cases that much like M&G, with the multiple dies,
multiple annealings, and case trimming and extreme reworking of regular rifle actions,
which is why I like our 585 case, simple and straight, any regular, long bolt action, or
falling blocks, break actions, etc, a 585 good for dozen or more heavy loadings,
and moderate loads, last forever..

For our 585HE , made it a size, actually new belted size, to fit regular size, long bolt guns,
(not BMG actions)that didn't have to be used from tripod so to speak, and could be put in a favorite
gun of many, the Ruger #1, other falling blocks, without taking metal out of the feed trough.
To get the same and/or more powder space as a cut back, really shortened, BMG case, like M&G,
wildcatted to 585, or other short cases, we made longer case and worked with guys
with a group buy, to get a factory run made. A miracle. We thank all gun nuts for the help.

Here is picture from the great site, cartridgecollector dot net, of the M&G Mag .Ed

575%20MG%20MAGNUM%20FULL.jpg
 
Interesting thread, so much info in one place to sort through. :)

Maybe it makes sense to break it up into a thread for 12 gauge size, 20 gauge size, 24 gauge size? Otherwise it takes days to sort through.

So if a person was thinking about 20 or 24 gauge for slug use, would it make sense to increase the twist to maybe 1:12 and use 416 of 458 ceb or GS custom safari bullets as the slug?
 
I assume you mean using them in 24ga .585" and 20ga .620" sabots.

For 20 .620", and 24 ga .585", 1 to 20 twist has been fast enough.

Our McGowen 585 barrels are 1 to 20 twist and they stabilize

.458" bullets we used in the 585 sabot ok, as we got them

out at good speed of over 2300. They have fast rotation. Ed
 
It's always a balance between the gun I would like to shoot and what I really should be using with a rebuilt shoulder. (not from gun use, skiing)

What I had in mind was a longer, boat tail bullet for the slug, like a 416 or 458, roughly 1.5 inches long for the higher BC. Those take care faster twist then the flat tails.

Your setup is really impressive, I am just asking questions about how far the idea has been stretched.

I am quite sure that the 12 gauge HE is past my threshold, still thinking about the 24 HE. I saw a video of a big guy, properly holding on and firing a 577 ne, pretty impressive.

Also still bending my mind around the idea of using a somewhat higher pressure slug in 24. Very innovative, just dealing with mental inertia on my side.
 
Sorry to be away so long. Health and money problems.
Here is how the top of the singlestack magazine looks that we
made to use in Enfields and other bolt actions. The lips that hold the
cases are springy, and we can load it from the top. The inside of action
below feed rails are relieved a little and that allows feed lips to
move and work ok. A wider version of this magazine would work
for 12ga, etc, with brass cases, like in Savage 210.

topmag.jpg


Here are couple 24ga FHs break actions, a CBC with monoblocked
585 barrel in it, and a guys NEF he had a 585 barrel monoblocked in.
The 585 barrels are perfect fit for 24ga, and 585 Minie Bullets
are a perfect for barrel and 24ga case fit.

24gacbc.jpg


nef24fh.jpg



Another matter---It is humbling for me to ask for help when
I ask guys on the net for help at times.But I really am in a bind.

That is truth, Our small income we had from our farms truck garden
business is no more, as my my knees are shot and can't hardly
walk, I can't do field work, etc. And the wife's lung condition
got so bad she can't work.We both getting old.. So we finally quit that,
but were and are in debt. We need little extra money to try
to keep our health fixed up and pay bunch of back bills and utilities.

Could you all maybe get together with others on these forums
and kinda take up a collection to help get me out of my troubles and
debt. Like 10-20 or so bucks each put into our paypal account as gifts.
And if you want to mail it, contact me to get you
my mailing address. The Paypal email is [email protected]

Best Regards- Ed

PS-- We really need help. Not astronomical amounts, but fairly fast.
Just a little from each to help. A quick boost so to speak.
We never made anything on the 12ga FH, 585, etc, work and
research and still don't.Ed
 
Here is picture of a lightweight Barnes bullet in 24ga FH.
Guys cut the back off of 750gr bullet off to get 500gr weight.

24litebarnes.jpg


Here is picture 58 cal Minie slug that's little long for our 12ga
sabot, with the front of the slug above the grooves swaged
to fit in sabot. The swaged front third of the slug fits next to
the internal ridge in sabot and the sabot doesn't bulge out.


slugswage.jpg


And some info about 12ga FH and other hopped up shotgun slug loads,
You know we like to use the rifle, IE slower than shotgun, powders.
We like to use IMR 4759 for some loads and RE17 for others where
we have room for larger charges. Those two powders are ignited ok in large
diameter cases like 12ga, 10ga, 16ga, etc, without needing BMG primers.
But we have always been looking for easy to ignite powders of the RE17
type, when cold, that has a speed between IMR 4759 and the RE17.
RE17 uses different process to put the deterrents in the powder to control
speeds, which allows much easier ignition, compared to big majority of rifle
powders with all the deterrent on the outside.

There are some out there made by Nitrochemie Switzerland, who makes
RE17, RE26, RE33, etc, for Alliant. It's the ' RELOAD SWISS' brand available
for those in UK and Europe, They are called RS 40, about same speed
as RE12, RS 50 & 52, same speed as RE15, RE60 & 62 same as RE17.
Also one ' Vihta Vouri ' powder called TR140 available over there,
that Nitrochemie made..

Many guys can't get IMR 4759 anymore, some can't get RE17.
I'd like to get some of RS 40-50-52 powders or V V TR140
into the states, would really be great help for hairy slug load work. Ed
 
We got guys wildcatting our 585HE case,


375warlord2.jpg


Here is picture of that 375 Warlord next to our 585 case he made it from.
He is going to make couple later necked down to 416, and 458.
There is another guy working on doing one necked down to 357 wildcat.

375warlord.jpg


Here is a picture of our poster Biebs on AR, 585 HE, in a MPI stock.
He used a big Enfield action, with a fancy jeweled bolt.

biebs2.jpg


We found couple other big actions for our 585, that can even feed really
long overall length loaded cases, like 4.5" long or more, if you are
using long pointed bullets for real long range target and hunting work.
One is Lawton 8000 Cheytac action, and the other is Stiller Cheytac actions
made similar, just a newer version. Both actions come in 1.45" diameter
and a 1.60" diameter receivers.

And Vestals Gunsmithing in Virginia does great work, decent prices, has
these actions and will build you fancy 585 HEs. .. He has, working with
another guys mag box setup, setup an extra long, good working, single
stack, center feed, magazine..He has one of our 585 HE reamers on hand,
we have barrels....Ed

lawton8000.jpg
 
Best case sizer is the MEC Collet Super Sizer and it can double
as a case holder when we roll crimp. Much better hold than
the ones made to hold cases for crimping, that cost a lot.
Save cost of a holder, plus have best sizer around

mecrimp.jpg


Here is couple different setups our guys checking for our 585HE
in a long, Lawton Cheytac action. First laminated thumbhole stock.
Second in a Hogue Compstock. The action can mount a scope rail
like shown on the table in 1st picture or a receiver sight in 2nd picture.
The scope rail is a piccatiny,. if you need long range work.

lawtonthumb.jpg


lawtonhogue.jpg


The stocks used were wide ones for REM long actions, just add recoil
block ahead of recoil inleting for the longer action, drill new screw hole
Open the stock forward to original bolt hole for longer cases and mag.

About Enfields for our case, one of my favorites, Some don't like the
sporterizing, welding bottom metal straight. Many think straightening
is a huge job needing special jigs, etc, Not really, just use one for a jig
with a bolt, to weld on the straight extension, Do top weld, then cut old
extension that is under off with a thin cutting wheel, then weld bottom.
When we bolt the short piece on the one we are straightening, we grind
the short slant off so the added piece lays on there flat.
The one you cut off can be used as the top extension for the next one!!!
Just keep on building...Ed

guardlen.jpg
 
Best case sizer is the MEC Collet Super Sizer and it can double
as a case holder when we roll crimp. Much better hold than
the ones made to hold cases for crimping, that cost a lot.
Save cost of a holder, plus have best sizer around

mecrimp.jpg


.
 
Here is a fancy stocked 24ga FH built on a NEF, built by
a guy in Canada. Its straight back, high comb
stock, handles recoil great.Neat looking work... Ed

brian24.jpg



About our 2.17" 585 BB case for lever guns, pistols, etc,.
It is made from our 585 case cut back to 2.17" long.
With loaded length of about 2.8" work in lever guns, etc.
Work in 71s, later 1886s, Henry steel frames made for 45-70.
One guy is putting one in single shot action set up with
Contender style pistol grip for testing in long rifle barrel,
to simulate pistol recoil..Be very brisk recoil in a case
that holds 110 gr powder under a light Minie bullet.
Maybe work in a Rossi Judge with heavy barrel.
Or rolling block rifles and pistols...Gonna try one in 1887.
Got first one in one of our guys Greener GP for testing..

In some ways big bore shotguns and rifles are sexy.
By looking at the shape of the fire and smoke cloud....
Thanks for picture, to the great NitroExpress Forums site.


Mickyboob.jpg


Here is picture of another neat sporterizing deal for Enfields.
On those without rear bridge pocket welded up, we just mill down
and shape it so debth of the pocket matches bottom section of
weaver rail and screw or epoxy it in. Shape to drive in hole tight.
Can use as a rear scope ring mount or mount for peep sight
like a compact UTG sight...Ed

enfieldsight.jpg
 
Warning! This thread is more than 6 years ago old.
It's likely that no further discussion is required, in which case we recommend starting a new thread. If however you feel your response is required you can still do so.
Top