270 Win Found My Recipe

cajun said:
How many grains up or down were the other loads and how did they shoot? Reason I'm asking is Imr4350 is a great powder but velocities will change with temperature. I would shoot that good load in different conditions make sure it doesn't fall apart.
Click to expand...
That's what I'm thinking. I recently went through the same theming the last couple days. Out of five different charge weights the one in the middle of the range was half inch and the rest were two to almost five inches. So one really good group makes me nervous about that load. My other one was very good throughout all the charge weights most were approximately 1/2" out of 7 different charge weights the two worst were about 1 1/2" spread. So my thoughts are it was very consistent through the ladder test unlike the one the other day where I only
Had one good group and rest were bad.
 
Wow, in over 50 years of reloading of more than a dozen different calibers, several different powders, several different weights of bullets, and different manufacturer of primers, I have never shot a 5 inch group at 100 yds with a rifle or at 25 yds with a handgun.
 
meatyrem said:
That's what I'm thinking. I recently went through the same theming the last couple days. Out of five different charge weights the one in the middle of the range was half inch and the rest were two to almost five inches. So one really good group makes me nervous about that load. My other one was very good throughout all the charge weights most were approximately 1/2" out of 7 different charge weights the two worst were about 1 1/2" spread. So my thoughts are it was very consistent through the ladder test unlike the one the other day where I only
Had one good group and rest were bad.
Click to expand...
The max load is 55grs. I went down 1% from there for 10 steps down to 49.7grs I used excel to do my calculations and rounding. The lower I went the worse it got. IMR4350.
 

Attachments

  • IMG_6809.jpeg
    IMG_6809.jpeg
    234.5 KB · Views: 36
cajun said:
How many grains up or down were the other loads and how did they shoot? Reason I'm asking is Imr4350 is a great powder but velocities will change with temperature. I would shoot that good load in different conditions make sure it doesn't fall apart.
Click to expand...
The max load is 55grs. I went down 1% from there for 10 steps down to 49.7grs I used excel to do my calculations and rounding. The lower I went the worse it got. IMR4350.

Attachments

  • IMG_6809.jpeg
 
SecretSquirrel38 said:
COAL from the book is 3.340 and that is what I loaded to. I won't go above the book COAL when reloading any round. Factory rounds are typically below COAL.
Click to expand...
My TGK is at 3.36- max for my magazine. Still about .020-.040 off the lands as best I can tell. It shoots pretty good.

I have 200 Norma Tipstrike bullets. Max COAL didn't work very well. I lost velocity and accuracy. After deer season, I'm going to start walking the length down to see if I can find accuracy and velocity. If not, I'll have to try a different powder. I'm using Hunter right now.

Norma factory ammo with that bullet seats REALLY deep. My last rounds were 3.320 about .020 off the lands.. Factory is about 3.170. I've found recommended COAL from 3.169 to 3.300
 
The 140 Tip strike is very accurate in an old well worn Ruger 77. 200 yd groups are very impressive, with H4831 with cci 250s, plenty good enough for a short range woods gun. Sorted Ogive lengths are as good as the best lots of berger bullets. I have yet to kill a deer with these tip strikes. I cut a bullet open, peeling back the jacket to the base. There is a very impressive Lock on the core in the base of the jacket, much more than the Hornady Interlock.
 
Last edited:
VinceMule said:
The 140 Tip strike is very accurate in an old well worn Ruger 77. 200 yd groups are very impressive, with H4831 with cci 250s, plenty good enough for a short range woods gun. Sorted Ogive lengths are as good as the best lots of berger bullets. I have yet to kill a deer with these tip strikes. I cut a bullet open, peeling back the jacket to the base. There is a very impressive Lock on the core in the base of the jacket, much more than the Hornady Interlock.
Click to expand...
Can you share your load data? I haven't used H-4831 yet but have some sc I can use. I've been working on Ramshot Hunter. It should work well if I can find the right combo but can switch if necessary. I have both CCI 200 and CCI 250 primers.

I would also be interested in your COAL, CBTO- seating depth, case length, etc. My rifle seems to be sensitive to harmonics so I'm looking for the right seating depth.

PS- I think I could take what I have an hunt. Groups are under 2". I have my OAL around 3.320 and velocities have fallen to mid-2800s. The factory rounds were seated deep AND very hot. I think they were about 50 fps over label which was already over 3000 fps.
 
I shoot 58.0g of H4831 with cci 250 in Win brass, bullet is close to the lands, 140 Norma Tip Strike. My throat length varies between the two barrels and I adjust seating depth accordingly. In another Rem 700, it shoots the same load with the 140g Nosler ballistic tip with bullets all opening up a bullet hole at 100 yards, bullets just barely kissing the lands.
 
Last edited:
VinceMule said:
I shoot 58.0g of H4831 with cci 250 in Win brass, bullet is close to the lands. My throat length varies between the two barrels and I adjust seating depth accordingly. In another Rem 700, it shoots the same load with the 140g Nosler ballistic tip with bullets all opening up a bullet hole at 100 yards, bullets just barely kissing the lands.
Click to expand...
No pressure?
 

Similar threads

G
270 win. H4831sc recipe?
Replies
4
Views
3K
moosekiller99
moosekiller99
G
.270 win recipe for hunting elk
2 3 4
Replies
42
Views
17K
nicholasjohn
N
Strick9
Help my Dads recipe
Replies
13
Views
2K
Strick9
Strick9
G
4831SC in my 270 win???
2 3
Replies
36
Views
23K
aushunter1
aushunter1
K
Found my load.
2
Replies
16
Views
3K
skipglo
skipglo

Recent Posts

Top