What type of bullet did you use on your last elk?

What type of bullet did you use on your last elk harvest?

  • Monolithic Solid Copper - Barnes, Hammer, GMX, E-Tip etc.

    Votes: 50 17.5%
  • A-Frame / Partition - or similar construction.

    Votes: 20 7.0%
  • Premium Bonded Lead Core - Interbond, Accubond, Scirocco, Woodleigh etc.

    Votes: 61 21.3%
  • Low Cost Traditional Copper Jacket Lead Core - Core-lokt, Interlock etc.

    Votes: 13 4.5%
  • Ballistic type hollow point with polymer tip, Hornady SST, ballistic tip etc. non-bonded

    Votes: 15 5.2%
  • Ultra Low Drag - ELDX, Nosler RDF, etc. anything designed primarily for drag coefficient

    Votes: 74 25.9%
  • Target /Match grade - Any bullet primarily designed for match grade accuracy above all

    Votes: 47 16.4%
  • Round nose, Flat nose, dangerous game etc. you like to hit them with bricks...

    Votes: 1 0.3%
  • Not sure, didn't matter because they all kill pretty much the same.

    Votes: 0 0.0%
  • Different bullet that doesn't fit a category. Excluding, arrows, trucks, spears ;)

    Votes: 5 1.7%

  • Total voters
    286

Golovkin

Well-Known Member
Joined
Feb 13, 2018
Messages
84
Pick the bullet that most correlates to a choice.

Also if you have a chance, tell us the muzzle velocity, and how did it do? Also note the impact velocity and range if you can.

Thanks for providing this info. As a long time elk hunter i'm trying to look outside my box and see what others are doing.
 
My elk: .375 cal., 250 Barnes TTSX @3130 muzzle velocity, only about a 250 yard shot, impact velocity approximately 2700 fps. Impact point, broadside, near base of neck, down immediately, bullet exited

Wife's elk: .338 ca., 225 Barnes TTSX @ 2950 muzzle velocity, about 200 yards, impact velocity approximately 2670, impact point, slight angle broadside, elk went approximately 20 yards, bullet exited

I could only vote once....but 2 votes for mono bullets. memtb
 
Last edited:
175 eld-x
impact velocity about 3000fps
It was a heavy bull, quartered to me, hit the heavy shoulder bone just above the knee dead center. It destroyed the heart and lungs and continued into the guts. No exit. Bull took a few steps and went down.
This was the shot I was a little worried about with this bullet, there's not a whole lot more punishing situation you can find for a bullet on north American game. It did very well.
 
My last elk a 100 gr.2 blade phat head on 420 gr acc.Elk before that 300 otm 338,2750 muzzle.One extreme to the other?
 
175 eld-x
impact velocity about 3000fps
It was a heavy bull, quartered to me, hit the heavy shoulder bone just above the knee dead center. It destroyed the heart and lungs and continued into the guts. No exit. Bull took a few steps and went down.
This was the shot I was a little worried about with this bullet, there's not a whole lot more punishing situation you can find for a bullet on north American game. It did very well.

That is impressive!
 
300 otm 338 at 2750,50 paces,exit about fist size.Tried to get set up on bull at 845 then it moved out of site.
 
Most recent elk was 225 gr eld-m 2800 fps at the muzzle and impact velocity of 1960 fps at 830 yards. One shot perfectly placed completely liquified his insides. Stumbled for 20 yards then tipped over and rolled to the bottom.
 
Nosler 7mm 140 grain E-Tip. Muzzle velocity was 2,780 fps. Shot her at 370 yards, don't know what the impact velocity and energy were. Bullet went through her.
 
Berger 215 Hybird. 300 Wsm 2650 fps. 455 yards. Behind the shoulder, but just a tad high. Bull never moved. Went down right where he stood kicked a couple times and that was it. My son went down and took care of the elk while I went for pack animals. So I don't know if it went clear through or not.
 
.338 cal 300 gr Berger at 2650. Bull was 250 yards away, hit a bit high and back. One lung was vaporized and the other looked like it was hit with a baseball bat. Found the bullet in the far side hide. Nothing but a jacket with a little lead. Bull DRT, but I have since switch to Hammer Solids...
 
Warning! This thread is more than 6 years ago old.
It's likely that no further discussion is required, in which case we recommend starting a new thread. If however you feel your response is required you can still do so.

Recent Posts

Top