It's a heavy target. Have a ultradyne max brake and this thing hardly even moves when shot. Super happy with it. Excited to put some hand load's together and see what it does after it settles in
-
If you are being asked to change your password, and unsure how to do it, follow these instructions. Click here
Howa 1500 308 accuracy issue
- Thread starter rafterjg
- Start date
Help Support Long Range Hunting Forum
Idaho Lefty
Well-Known Member
- Joined
- Jan 29, 2018
- Messages
- 1,785
You might think about, buying a Set of, Forster Dies
My 6 XC Forster Dies give me, a total Bullet "Run-out" of less than,.. .002 TIR
My 6 XC Forster Dies give me, a total Bullet "Run-out" of less than,.. .002 TIR
Idaho Lefty
Well-Known Member
- Joined
- Jan 29, 2018
- Messages
- 1,785
It's NICE when, a "Plan" comes, together !
Again,.. great Job !
Again,.. great Job !
How to the bushings work on those dies. I'm used to a rcbs die set
Idaho Lefty
Well-Known Member
- Joined
- Jan 29, 2018
- Messages
- 1,785
I don't buy any, Bushing Dies, all mine are, Regular, F L die sets.
The Forster Dies, are very Precise for, the New, Modern "Spec'd" Cartridge's like,.. 6 Creed, 6.5 Creed, 6 XC & both, PRC's ( held to, Tighter Tolerances ).
and,. have, VLD type, "Floating" Bullet Seating.
The Forster Dies, are very Precise for, the New, Modern "Spec'd" Cartridge's like,.. 6 Creed, 6.5 Creed, 6 XC & both, PRC's ( held to, Tighter Tolerances ).
and,. have, VLD type, "Floating" Bullet Seating.
Last edited:
M1A1ABRAMS
Well-Known Member
So do you believe the Tubbs ruined your barrel ?
I would probably say so. It's either that or the barrel wasn't a shooter from the beginning and I made it worse but hard to tell. But considering not many have issues with Howa it's a good guess that the tubbs caused it. Good learning experience for sure
I know a guy that threw a gun in the River...never had to clean it or worry about accuracy again!
Fire lapping with Tubbs is a last resort operation that rarely ends well.
Ugh...the Tubbs bullets had NOTHING to do with the original barrel being a dud. They didn't make it a dud. The barrel that came from Howa was just junk. It happens. Every manufacturer sends out a lemon now and again.
The real lesson here is SHOOT YOUR GUN FIRST BEFORE SCREWING WITH IT. Don't bed it. Don't free float it. Don't firelap it. Just test it out the way it came from the manufacturer.
I'm happy the gun shoots well with it's new barrel & the OP seems pleased. We all like a happy ending. Let's quit blaming the Tubbs product - it did not turn a tack driver into a turd.
The real lesson here is SHOOT YOUR GUN FIRST BEFORE SCREWING WITH IT. Don't bed it. Don't free float it. Don't firelap it. Just test it out the way it came from the manufacturer.
I'm happy the gun shoots well with it's new barrel & the OP seems pleased. We all like a happy ending. Let's quit blaming the Tubbs product - it did not turn a tack driver into a turd.
The onlu disappointment I have is the lack of help from Howa. Called and talked with a guy that was supposed to send me a service request form and never heard back from them
marksman1941
Well-Known Member
- Joined
- May 20, 2013
- Messages
- 1,025
Sometimes you have to chase it a bit. Usually howa does great CS. Everyone drops a ball now and then, and it's worth checking in after a few days to see what happened.
bonie
Well-Known Member
try 150 SST's at Sammi length, I believe I loaded them with IMR4895 , 1 hole five shot groups after break-in, out of my wood stock factory Weatherby, which says Howa on the Barrel, My son has the same results from a factory Browning X Bolt but he loads with H4895. also a wood stock . they seem to group well towards the higher end of the load data. you just may to find a node for your rig. good luck its sounds like you have a nice piece there.
