Thanks for the suggestions. Now I'm thinking I need to buy a few more actions! Haha.
-
If you are being asked to change your password, and unsure how to do it, follow these instructions. Click here
Have action need cartridge
- Thread starter dustbag
- Start date
Help Support Long Range Hunting Forum
Didn't find anything on Impacts website but according to Altus website looks like Lapua bolt face is not an option for the 777.
That's a bummer. Good luck with your other project builds.
My 338 Mega has a 21.5" barrel and my Rugged Alaskan handles it just fine. What is your big bore suppressor? The Ultra 7 would be fine with a 20" 300 Mega, 300 WSM, or a 300 PRC.
No 338 suppressor yet.
woodsman1991
Active Member
Within the confines of a 3.77 COAL, how well can the 338 edge / Rum perform? Is it limited to the 265 grain bullet range due to length of the big 300 grainers?
In order to play this game I would first need to look at what weight bullet I wanted to play with and then what type of performance I was looking to get with the length barrel i want to use. Then I would chamber accordingly. I feel like without any sort-of performance perameters the possibilities are so vast. But a new build of any caliber is exciting 
This is one of the reasons I went with the .338 NM/I over .338 LM/I.
The .338 LM and Edge need near or at 4.00" COAL to fully take advantage of the 300 Berger offering.
My .338 Thor (NM/I) with .300 Berger 3.7" COAL (touching the lands).
If it were my action and my money to burn, I'd go 7 PRC sized case, blown out to 338.
I would likely take 300 PRC, blow it out to 338 and then push the shoulder back for a more compact cartridge, targeting for 70-80gr of powder case capacity.
Load 300 grain long. Have someone use quickload or GRT to see about powders like H4350 / H4831 / RL17 - RL19 to get the best velocity and burn out of a 20"
You might even look at moving up to a 9.3 or even a .375, and could possibly use even faster powders.
If you think along the lines of a 416 Rigby -- 350gr bullet / 90-100 grains of powder and 20" barrel.
Whatever you build, with a large bullet and short barrel, the recoil will be stout.
I would likely take 300 PRC, blow it out to 338 and then push the shoulder back for a more compact cartridge, targeting for 70-80gr of powder case capacity.
Load 300 grain long. Have someone use quickload or GRT to see about powders like H4350 / H4831 / RL17 - RL19 to get the best velocity and burn out of a 20"
You might even look at moving up to a 9.3 or even a .375, and could possibly use even faster powders.
If you think along the lines of a 416 Rigby -- 350gr bullet / 90-100 grains of powder and 20" barrel.
Whatever you build, with a large bullet and short barrel, the recoil will be stout.
Will.284
Well-Known Member
I e built 7 prc's now it's time for 2-300 prc's why 2 you ask ? So they don't get lonely
Lefty7mmstw
Well-Known Member
Put it in a 22" bbl. and it'll probably perform about like a 338win in a 26" bbl., which is to say not too dang bad. I'd think long and hard about a 338rum on a 22" bbl. if I were the op..
I have a long barreled edge being built and a long barreled 300 rum already. Thinking between 30 Nosler or 300 prc. Although @KH_Outdoors 338-300 prc looks pretty nice.
I am glad you finally shared that info.
