barrel

18” 22 NXS. Rifle length gas. I built 24” for more speed. Uses necked down 6 Hagar brass and 6.8spc bolt face. 22 nos will not shoot in this chamber. Holds a few gns more powder. Has about 150 down the tube. Shoots 3/4 with 53 vmax at 3400, or 3100 with 73 elds. Minute of a coyote. I’ll take...

Have a savage stainless steel small shank barrel in 7mm mag. 24" long. Bought from NSSF auction. I have never fired it and dont think it has ever been fired beyond the factory. I bought it to use the action for a build. There is a small marred section 6" from the muzzle shown in the...

This barrel is nearly new, put 40 rounds through it before my brother talked me into building a 28 Nosler instead! This came off a new factory Remington Sendero purchased in 2019. It was threaded for a 5/8x24 muzzle brake. This is a great option for anyone looking to rebarrel their Sendero...

Looking to sell a brand new remage ragged hole barrel. Its a #3 contour Wilson, fluted, threaded and with the barrel nut, chambered in 6.5 CM. Was going to turn it into a 6.5 PRC but decided to go a different route. Asking 250 plus shipping cost.

Shaw barrel, flutted, recessed crown, in the white, 18 inch, threaded for large ring Mauser 98. Barrel is fully chambered and marked 308 Winchester. $100 shipped to you. USPS money orders or check payments

I recently replaced a Tikka T3X .300WM sporter barrel with a factory take-off barrel that was threaded so I could shoot suppressed. Upon checking the headspace, the bolt closed on a go-gauge, but also closed on a no-go gauge. However, upon adding a piece of scotch tape (roughly another .002") to...

Title pretty much says it all. I bought this barrel six months ago but before it showed up I found one for my build. 300PRC machined in house by proof research to screw directly onto an impact long action (787r) without any gunsmithing required. Barrel is 24” with 5/8x24 muzzle thread. 1:9...

Just trying to plan out my path forward in this shooting endeavor. My 6.5 CM with 24” Benchmark #5 contour barrel has just crossed the 1400 round count mark. I shoot about 40 rounds a week AND one to two rounds during hunting season, depending on how steady I can get. I have accumulated the...

For sale, a new, uncut and unchambered Hawk Hill .30 barrel blank. I picked this up in person a few weeks ago, as the HH is a local shop. It is a 28" blank in their heavy varmint contour, with 1:9 twist rate and 4 groove rifling. Very nice, quality made barrel, typical Hawk Hill. Asking $350...

Proof Carbon fiber prefit for Zermatt Origin action. 6.5 creedmoor. Sendero contour. 24". 1:8. 330 rounds. Lots of barrel life left on it. Shoots great. Just decided to go with a different cartridge. $600 shipped

Up for sale is my 16" Faxon Gunner 6.5 Grendel AR 15 Barrel. This barrel has about 500 rounds through it with plenty of life left. It is 1:8 Twist, 5r Rifled, melonited 416 Stainless steel with a nickel boron coated barrel extension. It fit nice and tight in the upper it was on and regularly...

First off I am an avid hunter, absolutely new and green to the reloading process and long range shooting. I have a cousin that is a genius at this and have talked much with him on suggestions / feedback which has led me to start shying away from standard rifles and delve into custom. my...

i have a ruger carbine 10/22 blued take off barrel for sale it does have some scratches from use i will get pic asap 50$ buyer pays shipping

Bought this barrel from Ryan and ended up going a different direction. Paid 450 plus tax and shipping. 400 shipped to your door.

im looking to buy a ruger 10/22 stainless steel barrel for around 60$

Got a 6.5-06 24in SS remington 700 barrel, appears to be a custom barrel only markings are caliber stamp .80 inch at muzzle. 1-9 twist(cleaning rod test) riflings look very good looks like a low count tube 150$ shipped, if no interest I'll throw it on ebay

26” Stainless factory barrel from .300 Win Mag, Remington 700 Sendero. Fluted. 1:10 twist. Sendero profile. Less than 300 rounds. $150 obo.

As described above, pair of Krieger .284 stainless barrels. Should be able to get info off invoice sheet. Both are #5 barrels. I'm in south central Wisconsin should someone local want them. $310 for one. $600 for both shipped to your door assuming CONUS. Will ship minute check clears. USPS...

Used but in excellent condition, factory Savage Model 12 Varmint take-off barrel. Stainless, Cerakoted FDE, 1:12 twist, unknown exact round count, but I have shot maybe 30 rounds through it, while the previous owner reports firing about 80 rounds. It seemes to like the UMC Remington 50gr HPs...

Bought this from a gunsmith a little while back with the intention of making me a nice long range .308, but now need to fund other plans (personal wildcat build). It is reported to have less than 50 rounds through it, as the previous owner wanted to to something similar to what I'm doing with...