I had a Ruger M77 270 with the tang safety. It was a very good rifle but the trigger, like yours, needed some help. The last M77 i got in I ended up changing out springs and honing/polishing the internals to fix the trigger pull but it was a slow, tedious process.
-
If you are being asked to change your password, and unsure how to do it, follow these instructions. Click here
Rebarrel vs buy a Tikka
- Thread starter nksmfamjp
- Start date
Help Support Long Range Hunting Forum
Yep the Mark series are way easier I am told. But I have a lot of history with this old Ruger. Killed my first Elk with it and many after that, had to have the barrel replaced and man it shot so much better. I'll never sell that rifle.
I botched a bedding job in mine as a teenager. Stupid is as stupid does and I was stupid. Later I needed some money and sold it. I killed a trainload of deer with that rifle and won many of our little unknown distance $5 ante Sunday evening neighborhood shootouts. It was a cold bore killer. I really wish I had it back. I later bought one of their polymer cutout stocked stainless rifles but I never could warm up to it. Sold it and got a Model 70 Sporter in 270. I won't ever sell or part with it.
Rugers to me seem to give a bit more felt recoil due mainly to their stock dimensions and my physical characteristics. I get this with some of the Tikka's as well. I like to put a good recoil pad on them and cut somewhere between 1/8-1/4 inch of pitch into the stock. Or add a pitch spacer. Cuts way down on cheek slap and muzzle rise.
Got the M-Carbo trigger spring in and took less than 3 minutes to replace it. Be careful! The replacement spring from M-Carbo is small and I dropped it as soon as I opened it and looked for 10 minutes to find it. That was the longest part of the whole job.
Also some use a screw driver and cross thread the screw into the threads. Don't shortcut it by not removing the trigger assembly as it is easy to cross thread it they say. Mine went fine and even though I thought I wanted a 2 pound trigger I was happy with a 1 pound 6 oz trigger pull.
Let me know how your Mountain Tactical trigger spring does.
nksmfamjp
Well-Known Member
- Joined
- Jan 5, 2004
- Messages
- 3,466
Well, I ended up ordering from a guy on Accurate Shooter….
I just got in from doctors and will have my knee surgery Tuesday early in the morning so I may not read how yours went until a few days later.
I wish you well and a good report my friend.
I wish you well and a good report my friend.
Did it! Your right bultinkle . Even on trigger adjustments I always slam the butt on an empty chamber just to make sure.
Also good to engage the safety, then pull the trigger a couple times, then flip the safety off with a little authority and see if the hammer drops. I've had that happen once or twice when using lightened sear engagement springs.
Anytime I mess with a trigger my first rule is to loctite any set screw unless it's a detent type screw under spring pressure like on Triggertech triggers. This is particularly important with Walker type Remington triggers. I'll then pound the recoil pad down on a table or floor or hit it a few times with a dead blow hammer or mallet both with the safety off and on. I'll also work the bolt vigorously several times while dry firing
to make sure the hammer didn't fall during the cycle. Work the safety on and off vigorously as well. I've seen many of the old Walkers vibrate loose from firing and become dangerous after a novice trigger job.
At one time I had done several standard Savage Triggers with good success. I guess I got a bit too confident and did one that I tested and it passed everything I threw at it. The next day I went to zero the rifle and the hammer fell when I cycled the bolt on an empty chamber thank goodness. Now if anyone wants trigger work on a Savage non accu trigger the only option I offer is replacement with a Timney. I learned my lesson on that one.
to make sure the hammer didn't fall during the cycle. Work the safety on and off vigorously as well. I've seen many of the old Walkers vibrate loose from firing and become dangerous after a novice trigger job.
At one time I had done several standard Savage Triggers with good success. I guess I got a bit too confident and did one that I tested and it passed everything I threw at it. The next day I went to zero the rifle and the hammer fell when I cycled the bolt on an empty chamber thank goodness. Now if anyone wants trigger work on a Savage non accu trigger the only option I offer is replacement with a Timney. I learned my lesson on that one.
