I never stop learning----This weeks lesson herein

Well, I believe that the bullet is being forced back toward the center a bit. But I appreciate your opinion.

I'm also thinking that large amounts of runout could be the equivalent of a chamber ream not being concentric woth the bore, which I do believe woukd be near the top of.the list of potential accuracy problems. I'm no expert, just talking here. The results on target will ultimately determine how much I care and how much effort I will put toward fixing any runout issues.
 
Ol' Red said:
When I got my concentricity gauge I measured some .300 win mag loads that I just finished. The worst one was .002" runout while most were less. I thought that I wasted money on the gauge or it did not work. For the next hour or more I was digging out boxes of reloads and some old factory loads from 20 years ago. The gauge worked just fine. I found that rotating the shell three times while seating the bullet helped. I also found one set of .308 dies just needed to be replaced.
Click to expand...
Which gauge did you get and are you happy with it?
 
The gauge I got is a Redding. I like it....its simple. The hornady model is set up to 'adjust concentricity' as much as it is to measure it. I woukd not personally want one of those. Just my two cents.
 
I'm definitely "NOT" going down that "rabbit hole"……I have too many mental issues!

I have a method…..approved by the SWAG system of hand loading. I go through the usual loading steps, minus a few that you guys use, however when seating the bullet……I fully seat, rotate the loaded/seated cartridge 180 degrees, then seat again.

I can't attest to this as helping minimize runout or just screw things up twice! 🤔 But, I get groups about as good as possible considering……the shooter, the cartridge, the load, the rifle/scope combination, and felt recoil which may fall into the shooter category. I constantly get one hole @ .375"…..until I fire the second shot! 😜 memtb
 
memtb said:
I'm definitely "NOT" going down that "rabbit hole"……I have too many mental issues!

I have a method…..approved by the SWAG system of hand loading. I go through the usual loading steps, minus a few that you guys use, however when seating the bullet……I fully seat, rotate the loaded/seated cartridge 180 degrees, then seat again.

I can't attest to this as helping minimize runout or just screw things up twice! 🤔 But, I get groups about as good as possible considering……the shooter, the cartridge, the load, the rifle/scope combination, and felt recoil which may fall into the shooter category. I constantly get one hole @ .375"…..until I fire the second shot! 😜 memtb
Click to expand...
Thanks for that, it made me belly laugh.....we need to remember what the weakest link in the chain usually is, don't we!
 
Bang4theBuck said:
Well, I believe that the bullet is being forced back toward the center a bit. But I appreciate your opinion.

I'm also thinking that large amounts of runout could be the equivalent of a chamber ream not being concentric woth the bore, which I do believe woukd be near the top of.the list of potential accuracy problems. I'm no expert, just talking here. The results on target will ultimately determine how much I care and how much effort I will put toward fixing any runout issues.
Click to expand...

I 100% applaud your effort to find out for yourself!! 👍......If more folks took that approach there would be less useless old wives tales floating around.
 
memtb said:
I'm definitely "NOT" going down that "rabbit hole"……I have too many mental issues!

I have a method…..approved by the SWAG system of hand loading. I go through the usual loading steps, minus a few that you guys use, however when seating the bullet……I fully seat, rotate the loaded/seated cartridge 180 degrees, then seat again.

I can't attest to this as helping minimize runout or just screw things up twice! 🤔 But, I get groups about as good as possible considering……the shooter, the cartridge, the load, the rifle/scope combination, and felt recoil which may fall into the shooter category. I constantly get one hole @ .375"…..until I fire the second shot! 😜 memtb
Click to expand...
I have the Hornady concentricity gauge and have straightened many bullets with it.
I really like memtb's idea of turning the seated bullet 180 and seat again,sounds like it work well!
 
Plus one on the Forster full length sizing dies. I'm very impressed with mine. I don't want to disparage anyone else's but the Forster's are definitely top notch. For seating, two of the best seem to be the Redding Competiton Seater dies and Forester Bench Rest seater dies. I own both and both are very good. Most that comment on them seem to give the nod to Redding and I would probably have to agree. This set up of sizing and seater dies will produce very concentric ammo. What I am currently thinking about now is to pull the expander plug from the sizing dies and expand the case necks separately with a mandrel. If there is a weak link in the process of reloading concentric ammo, it's probably the expander plug. Lubricating the case necks helps and perhaps polishing the expander plug could possibly help too. Starting with good brass will also go a long way.

In addition to sorting brass with the concentricity gauge, this little guy can take it one step further.
1730416664321.png
 

Similar threads

sextonds
Interesting Lesson
Replies
5
Views
852
LVJ76
LVJ76
J
Curious, never seen this before
2
Replies
16
Views
4K
mdvctry
M
MASH
Never seen a primer do this before.....
3 4 5
Replies
58
Views
24K
MASH
MASH
A
Temperature Learning Experience
Replies
10
Views
3K
J E Custom
J
E
New gun, how do I find a LR load in 2 weeks?
Replies
9
Views
3K
Forester
F

Recent Posts

Top