• If you are being asked to change your password, and unsure how to do it, follow these instructions. Click here

.550" vs .600"?

R

RichCoyle

Well-Known Member
Joined
Jun 26, 2023
Messages
411
Location
Grants Pass, OR
Do you experienced shooters think there would be any difference in cold bore shot with a muzzle diameter of .550" compared to a .600"?

I have an 8mm magnum with a barrel diameter of .600". The other da I fired a cold bore shot at 300 yards and then a follow up shot as though I was hunting. The "group" was 2 1/4". I'm thinking about a new 7mm magnum and using a .550" barrel. Could I expect that kind of performance with the lighter barrel in 7mm?
 
Hmmmmm, I have 2 very skinny barreled rifles, one is a Kimber 8400 in 300WM that will print 2 rapid shots under 1 MoA with ease, but walk a third shot at least an inch away.
The other is my REM 700 SPS in 300RUM, it didn't walk 3 shots at all in rapid fire, all were under MoA in a clover leaf and with slow shooting it printed 10 shots into MoA @ 100 without issue while breaking in the barrel. I was very impressed with this performance from a factory barrel and factory Barnes 180g TTSX.

Normally, I would say that a skinnier barrel is more likely to walk shots as it heats up, but now I honestly think it depends on the barrel itself and not necessarily it's thickness.

What rifling profile are you thinking of doing?
I believe this also makes a difference, 4 grooves has always been the best performer for me.

Cheers.
 
MagnumManiac said:
What rifling profile are you thinking of doing?
I believe this also makes a difference, 4 grooves has always been the best performer for me.

Cheers.
Click to expand...
I am thinking about using the Weatherby six lug ultralight profile from Pac-Nor. The Weatherby factory uses 24" barrels. Everyone knows you have to have at least a 26" barrel for a magnum.😊 The goal is a seven-pound rifle with a twenty-nine-ounce scope.
 
Thank you, Phil. I used Pac-Nor one time. Their fluting didn't take enough off to make much difference. I am going to gamble on a new 'smith in town. He has some CNC equipment, so at least if he programs things correctly my barrel will be fine. I hope.
 
The first local guy has known me a long time. He knew I was going to have a barrel fluted. When he told me he was going to give it a try I told him,
"I have a new barrel you can try on. If you mess it up, it's on me. If you are successful I don't pay."

He jumped at the chance. It had chatter marks, but was fine. He solved the chatter problem.
 
Phil Rizzo said:
I know it can cause hysterics, but don't forget that most top tier barrel manufacturers offer fluting in house.
Best way I know to give a little and take a little.
Click to expand...
I didn't include my Win Model 70 EW fluted barrels in this discussion due to them being fluted and Magnums. They have 3 factory barrels in 264WM, 300WM & 338WM, but the 264WM rifle has barrels in 257 Weatherby & 270 Weatherby, unfluted at 26". The 338WM has another 264WM barrel that is unfluted, this was my first test at using the A191 reamer design and it worked marvellous in all respects.

I found these fluted barrels walked shots more so than unfluted barrels in the same cartridges. This may be the reason some barrels are worse than others for walking shots.

Cheers.
 
MagnumMania

Can you tell me more about your A191 reamer design and what you like about it. How does it shoot and how do the throats last in the magnum calibers ?

Thanks for sharing
Hal
 
I like to run smaller contours for weight savings and have not real issues. Of course the POI will shift and it has a lot to do with the overall rifle build and barrel quality. Barrel and cartridge combos vary as well. I typically get 4 to 5 shots with smaller cases and 3 or so shots with magnums. If the barrel is going to be threaded, I'd go for the 0.60 as the minimum. If you run shallow flutes on it, you can get the weight down a size but the flutes are really shallow and not worth the money for the weight savings, IMO.
 
A larger projectile will cause more barrel whip/vibration. 8mm to 7mm is 0.0393701 difference in thickness. So a barrel with using a 7 mm bore is roughly as stiff as a 8mm and .600 outside diameter
 

Similar threads

B
CZ 550 vs Ruger M77
Replies
10
Views
15K
Biggs300
B
N
CZ 550 vs Sako TRG
Replies
5
Views
4K
Nicholas
N
General RE LEE
600 Yards Max for Whitetail: 7mm STW vs 6.5 Creedmoor
7 8 9
Replies
115
Views
20K
mmgravy
M
H
Remington 600 stock
Replies
0
Views
539
hunterdude_josh
H
C
Cz 550 243 ?
Replies
4
Views
17K
Code4
Code4

Recent Posts

Top