But he's using a 26". I can run 2900+ with a 28" 6BR using lapua, alpha no way. I've tried it. It's not the case head, it's the web. They are so hard it won't expand and grip the chamber, causes bolt thrust and over headspaces and causes lift. Alpha does better in dasher since side wall is a lil longer, and the gt and creed cases all work well. Lapua is the best for a br variant.
-
If you are being asked to change your password, and unsure how to do it, follow these instructions. Click here
Defiance classic issue
- Thread starter Dmagna
- Start date
Help Support Long Range Hunting Forum
- Joined
- Jan 26, 2015
- Messages
- 1,828
Is there a burr around your ejector plunger? Is there stiff bolt lift associated with this? Might have missed it in your posts.
Case growth doesn't seem outrageous, but maybe a bit excessive. Does a fired case allow the bolt to close easily in the chamber? Have you tried reducing your load and jamming the bullet so as to keep the case head against the bolt face when fire forming?
Case growth doesn't seem outrageous, but maybe a bit excessive. Does a fired case allow the bolt to close easily in the chamber? Have you tried reducing your load and jamming the bullet so as to keep the case head against the bolt face when fire forming?
I PM'd you with my nearly identical experience also with a defiance action. It came faulty with a substantial burr around the plunger ejector hole. Cost me a bunch of time, components and headache to finally figure it out. The bolt was eventually fixed by defiance free of charge, but that doesn't address the wasted time and components…
randy86314
Well-Known Member
I don't think you have a high pressure situation, except that the brass is soft for the pressure. Primers are beautiful. How hot is your load?
I reduced it by 1.5 grains to 30.5 grains of varget and it still produced large swipes. I have returned the action for inspection, hopefully they find something
Justice1327
Well-Known Member
Funny, i said the same thing on a FB post and was laughed at!
Strip the bolt and put a baggie over the bolt face or have your finger on the plunger to stop it flying across the room. Knock the ejector plunger retaining pin out. Run a q-tip head in and out going around the edge of the plunger hole. If it snags or you can feel it pull you have your answer. Just a light hit with a tapered round file will knock the bur off and put a slight radius on the very edge.
You could also use a cleaning pic to feel the edge. I have a whole set of dental pics I use for detail work . Very handy in a firearm tool kit. You could push your finger tip in tye plunger hole and rotate. If it comes out bleeding you have your answer. LoL
You could also use a cleaning pic to feel the edge. I have a whole set of dental pics I use for detail work . Very handy in a firearm tool kit. You could push your finger tip in tye plunger hole and rotate. If it comes out bleeding you have your answer. LoL
I'll let defiance work on it. I paid for a product, they have a warranty for a reason. If there was a burr or something I don't have the capability to fix it anyway. So they will take care of it.
xr650rRider
Well-Known Member
- Joined
- Jun 14, 2006
- Messages
- 46
All the problems might be the brass.
More than a few having issues with Alpha brass, not limited to 6BRA. https://forum.accurateshooter.com/threads/6bra-alpha-brass-question.4084271/page-6
More than a few having issues with Alpha brass, not limited to 6BRA. https://forum.accurateshooter.com/threads/6bra-alpha-brass-question.4084271/page-6
Tried different brass, same issue
Did you ever figure out what the issue was? What did Defiance end up doing?
I didn't want to mess with it anymore. Defiance looked it over cleaned it up, didn't change anything really. That action just doesn't like the dasher. I dunno, shoots other stuff fine
