Randy Tidwell
Well-Known Member
I measured my SA, bolts are approx 7.100" on center.
The one piece floor plates take small amount of inletting.
I had this one laser engraved.
-
If you are being asked to change your password, and unsure how to do it, follow these instructions. Click here
Model 70 Stock Replacement Question for the Experts
- Thread starter sjt18
- Start date
Help Support Long Range Hunting Forum
The one piece floor plates take small amount of inletting.
I had this one laser engraved.
sjt18
Active Member
When you said it took a small amount of inletting, what did you actually do? Did you have to build up then re-drill?
Randy Tidwell
Well-Known Member
No. Just opened the inlet a bit on the sides, the one piece are a bit wider and a tad longer. Very easy.
Let's back up here. What bottom metal is the Hogue stock inletted for? 1-piece or 2-piece? It'll be one or the other, not both.
sjt18
Active Member
2-piece.
This one: https://www.hogueinc.com/winchester-m-70-short-action-wsm-pillarbed-stock
They sell stocks for 1-piece but I was uncertain of the fit for my WSM.
Then you either need a complete 2-piece metal set and all 3 screws or, you need a complete 1-piece assembly and this adapter:
Winchester - M70 Short Action Stock Spacer to Adapt 2 Piece to 1 Piece Floorplate Adapter
Prophet River Firearms
The internal mag box, follower, and magazine spring you have are re-useable and the 3 action screws are re-useable. Nothing else from your 70A will transfer over to the Hogue stock. You need a complete short action 1 or 2 piece assembly, and the adapter above if you go 1-piece.
The 1-piece adapter and bottom metal assembly will be 1/4-1/3" "proud" beneath the bottom of the Hogue stock as that assembly is "deeper" and the Hogue rubber-coated Tupperware and AL pillar make it a pain in the rump to modify the inletting.
If you want everything to fit nicely without a bunch of rig-a-ma-row, then you need a complete 2-piece short action assembly.
sjt18
Active Member
You guys can't imagine how much I appreciate your insights. I guess I have decisions to make.Then you either need a complete 2-piece metal set and all 3 screws or, you need a complete 1-piece assembly and this adapter:
Winchester - M70 Short Action Stock Spacer to Adapt 2 Piece to 1 Piece Floorplate Adapter
Prophet River Firearmsstore.prophetriver.com
The internal mag box, follower, and magazine spring you have are re-useable and the 3 action screws are re-useable. Nothing else from your 70A will transfer over to the Hogue stock. You need a complete short action 1 or 2 piece assembly, and the adapter above if you go 1-piece.
The 1-piece adapter and bottom metal assembly will be 1/4-1/3" "proud" beneath the bottom of the Hogue stock as that assembly is "deeper" and the Hogue rubber-coated Tupperware and AL pillar make it a pain in the rump to modify the inletting.
If you want everything to fit nicely without a bunch of rig-a-ma-row, then you need a complete 2-piece short action assembly.
I guess I may have overthought that adapter. I was concerned that it was to convert a 1 piece to 2 piece.
When you say "proud", you mean it will stand rise above the plane of the stock on the bottom, correct?
Do you know or have an opinion on whether the action screws for my rifle would like up with one of the 1-piece stocks they have? I could probably swap the one I have.
There are adapters to go both ways. 1 to 2 or 2 to 1.
Correct
In reasonably recent (say mid-80's and newer for sure) M70 land you have 3 action lengths inletted into the top of the stock.
Long. This won't work for your WSM. Long action is anything on the '06 family, all of the belted mags, and the RUM's. The action-screw spacing is the same for all of them.
Short. This is what you need for your WSM. Anything marked M70 SA will have the correct hole spacing from 222 through 325WSM
WSSM. This only works w/WSSM actions. 22WSSM-25WSSM
You have 2 options for each length inletted into the bottom of the stock. 1-piece or 2-piece. There are adapters to go either way. 1 piece metal in a 2-piece inlet with an adapter will sit proud below the bottom of the stock. 2-piece metal with an adapter in a 1-piece inlet will sit flush.
Looking @ your pic from pg 2 here, and the diagram for the 70A on Numrich, it appears that your trigger-guard comes out, but your "floor-plate" is molded in as a solid part of the stock. If that's correct, you'll need a whole new assembly, 2-piece would be the easiest and best with the Hogue stock you have.
Last edited:
Randy Tidwell
Well-Known Member
I strongly recomend the HS stock over the Hogue. Far more stable. I've done a few Hogue sticks, not impressed.
Not sure what adapter they are talking about, I've never found the need.
If you buy a stock for the 2 piece setup, it can easily be opened up for the one piece. Stock for one piece will to big for the 2 piece.
JMHO
Not sure what adapter they are talking about, I've never found the need.
If you buy a stock for the 2 piece setup, it can easily be opened up for the one piece. Stock for one piece will to big for the 2 piece.
JMHO
