What cartridge are you shooting?
-
If you are being asked to change your password, and unsure how to do it, follow these instructions. Click here
Locktite marine epoxy and what release agent
- Thread starter bluedog69
- Start date
Help Support Long Range Hunting Forum
25-06
So I have read through my daughters "owners manual" for her newer 700 BDL. This one has the screw that is in the trigger itself.
This thing was set on 7 lbs factory. I can adjust the screw in the trigger and it goes down to 5 lbs. Take the screw completely out
5 lbs. I have tried watching youtube videos and that gets frustrating.
1) Do both pins drive the same direction to remove the trigger? I have seen several that drive both of the same direction which is what I did.
Other videos say drive the front pin L to R and the back R to L or vice versa even. Pretty sure I replaced them exactly as they came out.
2) After researching to see if I can adjust the trigger on down to 3 lbs I am left shaking my head. Some say the front screw sets spring tension. Others say that the back screw adjusts spring tension.
3) Have most people really threw their Remington triggers away and replaced them with after market?
I will probably just leave it set at the five pounds it is on and see if it helped tighten groups up any, Frustrating!!! My buddy said he takes all the screws through the trigger plum out and throws them away? Does it need to still be in there? If it was my rifle I wouldn't be as concerned, but since this is my daughters rifle.....
This thing was set on 7 lbs factory. I can adjust the screw in the trigger and it goes down to 5 lbs. Take the screw completely out
5 lbs. I have tried watching youtube videos and that gets frustrating.
1) Do both pins drive the same direction to remove the trigger? I have seen several that drive both of the same direction which is what I did.
Other videos say drive the front pin L to R and the back R to L or vice versa even. Pretty sure I replaced them exactly as they came out.
2) After researching to see if I can adjust the trigger on down to 3 lbs I am left shaking my head. Some say the front screw sets spring tension. Others say that the back screw adjusts spring tension.
3) Have most people really threw their Remington triggers away and replaced them with after market?
I will probably just leave it set at the five pounds it is on and see if it helped tighten groups up any, Frustrating!!! My buddy said he takes all the screws through the trigger plum out and throws them away? Does it need to still be in there? If it was my rifle I wouldn't be as concerned, but since this is my daughters rifle.....
Order a rifle basics trigger for it. Clay is a great guy to deal with and they make great hunting triggers. DO NOT REMOVE AND THROW AWAY THE SCREWS. They need to be in place for the trigger to work right. Which trigger is in it, the old Walker or the newer mark and then which version of the mark. The Mark's triggers are hard to adjust to a low pull, easier to just replace them. The walkers can be adjusted to a very nice result if u know what u are doing.
There is a sale on Triggertech Rem 700 triggers right now ($119):
www.longrangehunting.com
SOLD/EXPIRED - Triggertech primary independence day edition ($129.99)
Triggertech Primary independence day edition triggers on sale! Limited time sale - get one while you can! Right Hand With bolt release This fits remington 700 & clones https://jaoutdoors.com/product/triggertech-primary-trigger-independence-day-edition/
From what little I know from the last 40 years of Rem 700's. I think the old school like 1980's and 70's and maybe 90's? Had the Walker trigger. I have 7 mag that is an early 80's. (Walker trigger)
This one I think is a newer maybe even x mark II??? It has a screw in the trigger itself. Like where your trigger finger goes. That is the "screw" (singular) that my buddy said to throw away. ( not the ones glued in with epoxy)
Thanks again!!! I do appreciate the input!!!
Do you know for sure which way the two pins drive in that hold the trigger assembly itself?
I swear midway USA and brownell's and several others I have seen have conflicting both L to R , or front L to R and rear R to L directions for driving out pins.
Being a centre screw I would just straight out replace it. They are crappy triggers. The triggertech is a great option as is the Rifle Basix. As far as driving the pins it should be pretty easy to tell if there is a taper by pushing them by hand. Out of habit on domestic guns, out I push a pin left to right and in right to left. It doesn't take long to feel if you have pins that don't conform to the usual American standard. Most pins and the holes they go in it actually doesn't make any difference. Dovetails are a different story. They are tapered virtually all the time.
Thanks again for the great advice!!! Looks like I may be trigger shopping.
Now… TT or RB??? LOL
69, perhaps check contact with stock or bottom metal with aftermarket triggers. Some can occasionally bind due to slight size differences. I've had a few new triggers require a bit of inletting. Good luck
@bluedog69 either trigger is going to be great & a big improvement over what's in the gun now. I am with you - tinkering with the factory trigger would leave me uneasy. Just buy a good quality trigger & be done with it & have peace of mind.
Well I pulled the trigger.
Or, I will when it gets here.I ordered one of the Triggertech Primary Independence day edition triggers. If I like it I might buy 2 more. One of my other daughters shoots a 7 mag ADL and the other a 30-06 ADL.
I am just hoping it doesn't require any inletting. If it does oh well. I just hope if I have to file on the trigger plate(stainless steel BDL) I can do it clean enough my daughter doesn't notice. This one is very picky! LOL
I also bought a couple of those triggers. Hoping they will be fine for a couple of ADL conversions............Well I pulled the trigger.
I ordered one of the Triggertech Primary Independence day edition triggers. If I like it I might buy 2 more. One of my other daughters shoots a 7 mag ADL and the other a 30-06 ADL.
I am just hoping it doesn't require any inletting. If it does oh well. I just hope if I have to file on the trigger plate(stainless steel BDL) I can do it clean enough my daughter doesn't notice. This one is very picky! LOL
Triggertech are really good triggers. You guys will be very happy with them on any Rem 700 or Rem Clone action you put them on. After sales service on them is great as well.
"Well that was FAST" and "SHIPPING"usually don't end up in the same sentence nowadays.
I ordered this on Friday at 11:06am. Got it today on Monday at 12:20ish in my mailbox. How the USPS did that I have no clue?!?!?!?! But I will take it!
I ordered this on Friday at 11:06am. Got it today on Monday at 12:20ish in my mailbox. How the USPS did that I have no clue?!?!?!?! But I will take it!
