RUFFIAN R - NY
Well-Known Member
agree with most posted above just watch angle you cutting- if doing flat base may want to bell mouth the case just a little.
21st century expander mandrels 2-3 thou under bullet diameter, nice and round and neck tension setOnly because no one mentioned it:
New brass will have cases mouths that get out-of-round due to packing/shipping, etc. It's a good idea to run new brass through your sizing die before attempting to chamfer/deburr the cases.
Yeah, figured that one out with Lapua.Only because no one mentioned it:
New brass will have cases mouths that get out-of-round due to packing/shipping, etc. It's a good idea to run new brass through your sizing die before attempting to chamfer/deburr the cases.
I have imperial dry neck lube does that also work?Put a HEAVY chamfer on the inside of the case neck, NOT a deburr. HEAVY enough to where the chamfer almost goes to the outside of the case which would be better than just a slight de burr.
If you use Black Graphite on the inside of your case necks, you will see an improvement in bullet seating pressure and smaller groups. There are several ways to do this black graphite on the inside of the case necks, simple, cheap, and easy.
Imperial is really for resizing the case neck on the outside, but you can apply it to the inside with a q-tip, but powder might stick to the q-tip, the graphite is cheap and easy you have a little jar of small steel balls and you have a small jar of graphite, you put a little in the steel balls and then stab the case neck in and spin a little, inside and outside done, now mind you. this is 1 of 100 ways to do things. you need to experiment and figure out what YOU find what works for YOU.I have imperial dry neck lube does that also work?
I've gotten good at the basics then started seeing all the little fine details in it.some people lube the base of the bullet before seating, I am new to reloading metallic also, the best advice I got recently is, get a recipe out of a book for the components you have and load that recipe and get comfortable doing the basics well, and then start, seating depth and charge weights and such. but get good at the basics first! factory ammo shoots pretty good, so a factory recipe should work until we get to the lofty heights with the others.
Every case prep session I do the inside and outside as part of the process.So I'm on the newer side of reloading, only been using new casings. Just got some pulled brass and was aware of some burrs. What about chamfering? Is that something you all view as important? I saw redding had an inside chamfering tool and I did just get one with my Hornady Duo Prep Tool. This may be a stupid question to you all but did not see it in my reloading books (maybe I didn't look in the right place) so was just wondering what your guys' thoughts were?
Thanks
Heather, if you are reloading for hunting ammo, a lot of these very fine details are a waste of your time, and will be helpful only if you are shooting in competition. Keep it simple but precise and have fun shooting what you've loaded.Thanks guys. Didn't know how much there is to reloading. I'm on the younger side and haven't been reloading for long. So every bit of info really helps.
Thanks, I've been starting to get people that shoot for competition ask me to make their loads so it's important for me to learn, plus I hope to competition shoot as well with my Sendero 7mm STW that i plan on getting. I've got a boone and crockett edition chambered in the 7mm stw waiting for me right now.Heather, if you are reloading for hunting ammo, a lot of these very fine details are a waste of your time, and will be helpful only if you are shooting in competition. Keep it simple but precise and have fun shooting what you've loaded.
I hate to say this, but you just opened another can of worms (reloading for other people) that has been discussed in depth on this forum. Like everything, there is a wide range of opinions regarding the wisdom and risk of doing this, mainly because of the legal system we live in.Thanks, I've been starting to get people that shoot for competition ask me to make their loads so it's important for me to learn, plus I hope to competition shoot as well with my Sendero 7mm STW that i plan on getting.