NEW TO 6.5 PRC

Liberty4230 · Tuesday at 6:13 PM

Hello Everyone,
I am new to LRH so first of all, Merry Christmas!! Im hoping to get to know some folks and gain some knowledge. So I am trying to load some 6.5 prc loads. Test loads. I've been reloading for 30 years. Heavy for the past 20. Never for the 6.5 prc. I've resized my brass in my Hornady die. Done everything as usual.
When I went to seat my bullets......They fell in the brass!!!! What in the world am I missing? It's Norma brass and it does it with 130 grain Seirra Gamechangers and then I tried a 147 grain eldx with the same result!!?? I'm so confused. I load for 23 other calibers. I've never seen anything like this before? Any and all advice would be much appreciated!! Thank you!!

WeiserBucks · Tuesday at 6:27 PM

Bushing die with no bushing?

Longtine88 · Tuesday at 7:32 PM

K.E.C. Darkside · Tuesday at 8:02 PM

So what exact dies do you have.
A little more information will help us to help you. Are they bushing dies, are you using mandrel neck dies??

ARlife4me · Tuesday at 8:23 PM

if you're full length sizing with a correct die, then it shouldn't fall in. i've never used any bushings with any necks, so no experience there. i have been fl sizing everything for 40 years w/o issues like that even on 24x brass. was the brass from fired cases you've shot or new brass with correct headstamp? check the diameter of the 130tgk's and the 147edl-m's just to make sure they're .264". i'll retract my statement about no bullets falling in the brass as i have learned that sierra lengths (cartridge overall lengths) can be to long and to short when using their data. were you doing a dummy round (no primer, no powder) or fell in with powder @ your fill rate?

fill in thee blanks for help

stazmania · 2024-12-25T03:42:54-0600

following. I could play the speculation game but? oh well, wrong die, wrong expander, wrong bullet? Lets find out

Monterey21 · 2024-12-25T04:49:53-0600

WeiserBucks said:
Bushing die with no bushing?

If it's not that then the expander ball is for another caliber. 270 or 7MM

ARlife4me · 2024-12-25T05:18:12-0600

Here's a thunk, take a sized case and chamber it.

ARlife4me · 2024-12-25T05:19:53-0600

Measure the outside of the neck as Hornady might have labeled it wrong

ARlife4me · 2024-12-25T05:26:09-0600

Hornadys equal to the 277fury........6.8prc. And the news is out

ARlife4me · 2024-12-25T05:28:20-0600

ARlife4me said:
Hornadys equal to the 277fury........6.8prc. And the news is out

Or it's the dollar store version of the 6.8western

ARlife4me · 2024-12-25T05:43:31-0600

How authentic 6.8nes
North
East
Southern

highfinblue · 2024-12-25T06:35:36-0600

In forty plus years I've never seen anything like this, my guess is someone above has hit the nail on the head. Wrong die, bushing die with no bushing, wrong mandrel, something along those lines. New brass, if that's what you're working with shouldn't do that before you size it, so it almost has to be something with your die. I've been thinking about this cartridge quite a bit, following to see how it works out.

Bang4theBuck · 2024-12-25T07:25:16-0600

Does anyone else get rubbed when the OP lists their problem (especially when it is an interesting one) and then doesn't participate in the dialogue. Come on man!

NEW TO 6.5 PRC

Liberty4230

New Member

WeiserBucks

Well-Known Member

Longtine88

Well-Known Member

K.E.C. Darkside

Well-Known Member

ARlife4me

Well-Known Member

stazmania

Well-Known Member

Monterey21

Well-Known Member

ARlife4me

Well-Known Member

ARlife4me

Well-Known Member

ARlife4me

Well-Known Member

ARlife4me

Well-Known Member

ARlife4me

Well-Known Member

highfinblue

Well-Known Member

Bang4theBuck

Well-Known Member

Similar threads

Recent Posts