• If you are being asked to change your password, and unsure how to do it, follow these instructions. Click here

300 Win Mag vs 300 PRC

Guy M

Guy M

Well-Known Member
Joined
Jun 4, 2007
Messages
922
Location
Chelan Co, Washington
Had a lot of fun comparing these two great cartridges, one old, one new. They both do about the same thing, but with rather different cases and some other differences as well.

Got scorching velocity with the 180 grain Berger and the 300 Win Mag with Magpro powder. This was in 30 degree weather from a 26" Bergara barrel.

1734042229667.png



At over 80 grains of powder per cartridge, I went through rather a lot of Magpro coming up with this info. Fun though, I hadn't done much 300 magnum shooting in quite a while.

Regards, Guy
 
Only true difference is 3.34" COL to 3.6" COL.
You can do this, as I have done for 30 years, with ANY 3.6"/3.7" action with the 300WM, nothing new there.
Been using the A191 reamer for a decade or more, has the correct throat length for 215's to 230's……done!

Cheers.
P.S.
I like the 300RUM, Nosler, NMI & Lapua Mag Improved over the PRC case.
 
I like are the key words, I like my 300WM a lot, its solid using 210 grain SMKHPBTs and just plain fun to shoot it was my first 1762yd gun out at Fouled Bore in OK.
 
MagnumManiac said:
Only true difference is 3.34" COL to 3.6" COL.
You can do this, as I have done for 30 years, with ANY 3.6"/3.7" action with the 300WM, nothing new there.
Been using the A191 reamer for a decade or more, has the correct throat length for 215's to 230's……done!

Cheers.
P.S.
I like the 300RUM, Nosler, NMI & Lapua Mag Improved over the PRC case.
Click to expand...
This! I have 3 .300 WMs; 1 could accommodate nearly 3.7" COAL, and the other two around 3.5 - 3.6" COAL.
 
Thanks for this. I've always wanted a 300. Don't need it but still want it. Don't know why. I just do. The fact that I lean toward the older, tried and true means I wouldn't even give the PRC a glance. Brass would be no problem to find for the WM. The only other contender, for me anyway, is the 300 WSM as it appears to be very efficient and accurate. But then I'm not crazy about short action cartridges and I'm not sure the longer, heavier bullets would work well in the WSM unless I built it with a longer action.
 
Guy M said:
Had a lot of fun comparing these two great cartridges, one old, one new. They both do about the same thing, but with rather different cases and some other differences as well.

Got scorching velocity with the 180 grain Berger and the 300 Win Mag with Magpro powder. This was in 30 degree weather from a 26" Bergara barrel.

View attachment 624259


At over 80 grains of powder per cartridge, I went through rather a lot of Magpro coming up with this info. Fun though, I hadn't done much 300 magnum shooting in quite a while.

Regards, Guy
Click to expand...
I watched the video on UR. Always fun stuff. You two make watching the videos fun because both of you still act like kids in a candy store. A lot of shooting/reloading videos I don't make it through them just because they are boring and poorly made.
Thanks for the content, knowledge, and entertainment.
 
bluedog69 said:
I watched the video on UR. Always fun stuff. You two make watching the videos fun because both of you still act like kids in a candy store. A lot of shooting/reloading videos I don't make it through them just because they are boring and poorly made.
Thanks for the content, knowledge, and entertainment.
Click to expand...
Agreed!
 
If I wasn't so heavily invested in 300winmag, I probably would have gone PRC with my last barrel. But, I've had a winmag since I was 14, so I'm covered up in components and equipment.

Current tube is a heavy palma 1:9 Bartlein 5r at 26"
It was chambered saami (found that out after the fact) and throated for a 215 hybrid. Shoots good so I can't complain. Next time around, I'll probably go with the A191 or the Broz reamer. Not sure yet. I'm a little over 500 rounds on this one in two years time.

I've run magpro, H1k, and N570. Accuracy wise you couldn't tell the difference in any of them. N570 is awesome stuff bit it's smoking hot. I was running the 215's at a comfortable 2930. Magpro runs them just over 2900 and H1k was right there with it.

Just traded some primers for a jug of N165. Hopefully it works out well.
 
Guy M said:
Had a lot of fun comparing these two great cartridges, one old, one new. They both do about the same thing, but with rather different cases and some other differences as well.

Got scorching velocity with the 180 grain Berger and the 300 Win Mag with Magpro powder. This was in 30 degree weather from a 26" Bergara barrel.

View attachment 624259


At over 80 grains of powder per cartridge, I went through rather a lot of Magpro coming up with this info. Fun though, I hadn't done much 300 magnum shooting in quite a while.

Regards, Guy
Click to expand...

Was your loading done with virgin or FF cases. I had phenomenal velocities with N570 and virgin cases in my 300 WM with 215 Bergers. No pressure signs. Loaded what I thought was "the load" with fireformed and they were not having it. Had to drop quite a bit for the "real load". This was my first experience with needing to adjust for fireformed cases.
 
Rosebud said:
300 PRC, just because of the case design. No belt, no case separation at some point.
Click to expand...
If you believe that, then you ain't done much shooting….
Case head separations have ONE cause, and it has NOTHING to do with BELTS, just another myth believed to be gospel because someone said it, then it got repeated ad nauseam.

Cheers.
 

Similar threads

G
30 Nosler vs 300 Win Mag
2
Replies
23
Views
47K
Len Backus
Len Backus
jpfrog
.300 win mag - Accubond vs. Ballistic Tips
Replies
10
Views
11K
Nomosendero
N
D
CCI vs Remington primers for 300 win mag
Replies
13
Views
17K
rewinder
R
M
300 win. Mag
Replies
5
Views
2K
Double Dropper
Double Dropper
dana bodnar
300 win-mag
Replies
7
Views
2K
excaliber
E

Recent Posts

Top