6 CM brass to 22 CM

F

fmuguira

Well-Known Member

Joined

Nov 6, 2010

Messages

944

• Oct 17, 2024

• #1

Curious if anyone has ran 6CM brass through a F/L 22 CM die and had good results? No damaged /collasped brass, no doughnuts, etc. Looking at doing same as got a bunch of once fired 6CM brass and could put to good use in my 22 CM.

I ve sized larger caliber cases more than the .020 "neck down" successfully but dealing with smaller caliber stuff here.

ie: like 06 to 270 in one step and no lost cases or problems. Thx in advance for anyones 6mm to 22 caliber experiences !

 

FireFlyFishing

Well-Known Member

Joined

Aug 14, 2023

Messages

1,892

Location

Missoula, MT

• Oct 17, 2024

• #2

I can't answer your question outright. However, I know you need to anneal to accomplish the process.

 

Zen Archery

Well-Known Member

Joined

Dec 27, 2012

Messages

1,527

• Oct 17, 2024

• #3

I went 6.5 to 22CM no issues so 6mm will be no issue.

Yes anneal.

 

F

fmuguira

Well-Known Member

Joined

Nov 6, 2010

Messages

944

• Oct 17, 2024

• #4

Already annealed just wanting to see everyone's input. Have used friends bushing die before but figured if I could get by with std F/L die then even easier !

 

lancetkenyon

Well-Known Member

Joined

Jun 3, 2013

Messages

7,458

Location

Arizona

• Oct 17, 2024

• #5

With 40° shoulders, I say do it in 3 steps when necking down .020" (.273" to .253" +/-) like .266, .259, .253. I do that from 7mm to 6.5mm often.
For 30° shoulders, I would still do it in 2 steps (.263 & .253) myself.

Needed? Maybe not. But that is how I would do it. I try not to go more than .008" at a step.

 

S

std7mag

Well-Known Member

Joined

Dec 28, 2022

Messages

771

Location

Pennsylvania

• Oct 17, 2024

• #6

I've done many 7X57 Mauser and 8X57 Mauser to 257 Roberts with one pass through the 257 full length die.

They were virgin brass, so theoretically annealed from the factory.

Good lube, size, trim.

 

D

david g ranes

Well-Known Member

Joined

Sep 9, 2009

Messages

825

Location

Kansas

• Oct 17, 2024

• #7

std7mag said:

I've done many 7X57 Mauser and 8X57 Mauser to 257 Roberts with one pass through the 257 full length die.

They were virgin brass, so theoretically annealed from the factory.

Good lube, size, trim.

Click to expand...

I've done a bunch of it in one pass no issues couldn't find 22 creed brass when I had mine built but I did own a 6 creed. David

 

D

Dmagna

Well-Known Member

LRH Supporter

Joined

May 30, 2018

Messages

2,144

Location

New York

• Oct 17, 2024

• #8

You won't have a problem. Just check length after

 

Josh06

Well-Known Member

Joined

Sep 17, 2019

Messages

336

Location

Fort Worth, TX

• Oct 18, 2024

• #9

I went 25cm to 22cm with no issues.

 

W

westexhunt

Well-Known Member

Joined

Sep 9, 2013

Messages

304

• Oct 18, 2024

• #10

I've got four 22 CM rifles. Of the 1000 or more pieces of 22CM brass all but 200 were new 6cm run through a hornady fl die and loaded. No issues.

 

B

bob812

Well-Known Member

Joined

Nov 22, 2014

Messages

63

• Oct 18, 2024

• #11

You could also take the stem out of your seater die, run your brass through it then the full-length die. I do this with my 6-284 and 25-284. Works for me or maybe I just got lucky.