260 rem pressures

Coldfinger

Coldfinger

Well-Known Member
LRH Supporter
Joined
Feb 20, 2020
Messages
2,075
Location
Hills&Hollers
I finally got into 6.5 diameter. Picked up a 260rem from member. Just wondering what pressure spikes I should be noticing. Right now I'm cutting the same hole during pressure testing. I started at 41 gns h4350 and am sitting on 44 gns now. Launching Berger 140 elite hunters. Lapua lrp brass CCI Br2 primers.
No bolt lift resistance at all. But I know customs can hide pressure.
 

Attachments

  • image.jpg
    image.jpg
    262 KB · Views: 106
QL and GRT estimates 44 grains of H4350 at 69,878 and 68,925 psi, respectively. SAAMI max pressure is 60,191. QL and GRT data is based on a COAL of 2.8" and case capacity of 53.5 grains of H2O.
 
just_jon said:
QL and GRT estimates 44 grains of H4350 at 69,878 and 68,925 psi, respectively. SAAMI max pressure is 60,191. QL and GRT data is based on a COAL of 2.8" and case capacity of 53.5 grains of H2O.
Click to expand...
It's jumping a country mile to get to magazine length feeding but still cuts holes. There might be something to this 6.5 craziness I've ignored all my life
 
I don't see any signs of excessive pressure, but I would expect Varget to give better performance, it did in my 260 before I went AI with it, then H4350 shines over everything else.
What COAL/CBTO are you running?
My rifle is a REM 700 VSSF II, so mag length is restricted.

Cheers.
 
ShtrRdy said:
Primers look fine. Do you have a velocity measurement? That's another piece of information we can use to infer pressure.
Click to expand...
Not yet it rained all day. Don't have a garmin crono yet
MagnumManiac said:
I don't see any signs of excessive pressure, but I would expect Varget to give better performance, it did in my 260 before I went AI with it, then H4350 shines over everything else.
What COAL/CBTO are you running?
My rifle is a REM 700 VSSF II, so mag length is restricted.

Cheers.
Click to expand...
MagnumManiac said:
I don't see any signs of excessive pressure, but I would expect Varget to give better performance, it did in my 260 before I went AI with it, then H4350 shines over everything else.
What COAL/CBTO are you running?
My rifle is a REM 700 VSSF II, so mag length is restricted.

Cheers.
Click to expand...
I'm at 2.90" but got to get a tad deeper to not bind in Accurate mags. It's a surgeon action and bottom metal.
 
Coldfinger said:
I'm at 2.90" but got to get a tad deeper to not bind in Accurate mags. It's a surgeon action and bottom metal.
Click to expand...
OK, you should be good, I'm a tad shorter than you, but the AI chamber hides pressure real well. I'm at 49g H4350, no pressure signs. When mine was standard 260, I maxed out at 42g H4350 with 150g BT. Mine is 30" 8" twist.

Cheers.
 
43-45 grains of N160 with 140 sst is what I hunted deer with until I switched to a Grendel. I think it was 2700 from a 26" Austrian Mauser. I don't remember the coal but there is no limit on that action for the 260.
 
Fwiw Berger lists 40.8 gr with that bullet and powder. 2.8 coal.
Nosler doesn't list H4350 with 140 but has 43.5 with 130 gr. Berger uses quickload for a lot of their data so I would guess the above QL estimates are pretty accurate.
 

Similar threads

rharfo
Pressure 260 Rem load
2
Replies
14
Views
3K
scottishkat
S
W
260 pressure help
Replies
9
Views
3K
MNbogboy
M
RG300WSM
Pressures?
2 3
Replies
34
Views
2K
baldhunter
baldhunter
C
.260 rem
Replies
4
Views
774
Matt_C
M
S
260 rem
Replies
10
Views
3K
slayfire
S

Recent Posts

Top