• If you are being asked to change your password, and unsure how to do it, follow these instructions. Click here

Go gauge for shouldered prefit?

Is a go (no-go) gauge necessary for a shouldered prefit?

  • Fuhgeddaboudit. Screw it on and go shoot.

    Votes: 11 11.7%

  • Use a piece of virgin brass and some tape to calculate headspace.

    Votes: 9 9.6%

  • Use a go gauge and some tape for no-go.

    Votes: 30 31.9%

  • Confirm with both a no-go and a go gauge.

    Votes: 44 46.8%
  • Total voters
    94
quandary said:
I would think you should be able to take the barrel to a gun smith with the appropriate lathes that can bump the shoulder, adjust the threading etc to fit the barrel to the action.
Click to expand...

Taj said:
Barrel can be set back, but it will require a lathe. I have used virgin brass before when there was not a headspace gauge to be found, but it is not the best way. If the brass fits, add a piece of scotch tape to the base and try it. The tape usually runs about .0025-.003. Problem is, I have seen "match" brass vary as much as .002 to .003 in the same box. Measure the tape if you use it, I have seen some of it run almost .005.
Click to expand...
Yes, it can definitely be set back by a gunsmith. However that completely negates all the benefits of a prefit shouldered barrel, in my opinion. If you wanted a gunsmith to fit the barrel you would have been better off buying a blank and paying for the labor to start with.
 
clemens said:
Myself bit leary of the tape trick, How true is it that one can get a crush factor with tape?
Click to expand...
Yeah, you can't force it. It does work in a pinch. I have also seen a few factory guns that will close on a No-Go. That's why we have field gauges. As long as it won't close on a field gauge the gun is usually safe. I have also seen No-Go gauges that are under SAAMI max specs. Many gauge makers will tell you up front that their NO-Go gauges are under SAAMI max.
 
FrogFire7 said:
Yes, it can definitely be set back by a gunsmith. However that completely negates all the benefits of a prefit shouldered barrel, in my opinion. If you wanted a gunsmith to fit the barrel you would have been better off buying a blank and paying for the labor to start with.
Click to expand...

Of course thats the case. The question however was not whether you would want to do that. The question was why check with go/no-go gauges you can't do anything about it. My point was that you can in fact do something about it. The other solution is to send it back to the who ever reamed it and wait 6 months.
 
One can definitely set head space too tight either by "crushing" the tape or by using a nogo gauge that is under saami specs. which can result in a condition where some factory ammo will not chamber. If one is loading for a cartridge for which there is no factory ammunition the question becomes one of matching your chamber and dies.
 
Go Guage and tape works, I use go Guage and .001 brass shim. The issue with using the brass is until you fire a few you don't know if your undersize for your dies thus not seeing any sizing when you need it.
 
FireFlyFishing said:
Here's another way to look at the subject. Let's say you wanted a gunsmith to build your rifle. Would you expect the smith to use gauges, or just fudge it and hand you the rifle?

Let's say you built this rifle and it wasn't to your liking and you wanted to sell it. On the ad you fully disclose you didn't use gauges when building the rifle. How many people do you think you'd turn away from the sale?
Click to expand...
How many gunsmiths use a GO gage and shims and don't tell you about it as the buyer. It is within the gunsmiths responsibility to get it right. It is not a requirement to tell/teach the buyer how it was built.
 
This is the most overthunked thread I have ever seen on here.
A pre-fit for a PARTICULAR ACTION is a finished fitted product.
It requires no gunsmithing, it simply screws on and headspace and timing are done. Each barrel should be within SAAMI tolerances when CNC turned/threaded/chambered.
The only time you need go/no-go gauges is when you are cutting chambers.

Cheers.
 
pavementends said:
One can definitely set head space too tight either by "crushing" the tape or by using a nogo gauge that is under saami specs. which can result in a condition where some factory ammo will not chamber. If one is loading for a cartridge for which there is no factory ammunition the question becomes one of matching your chamber and dies.
Click to expand...
Huh? I get that SAAMI min can be just a smidge too tight, but how am I compressing tape to a negative interference. The tape is to ensure a loose, but almost min spec chamber. Hell, put 2 pieces on there….or foil.
 
MagnumManiac said:
This is the most overthunked thread I have ever seen on here.
A pre-fit for a PARTICULAR ACTION is a finished fitted product.
It requires no gunsmithing, it simply screws on and headspace and timing are done. Each barrel should be within SAAMI tolerances when CNC turned/threaded/chambered.
The only time you need go/no-go gauges is when you are cutting chambers.

Cheers.
Click to expand...

AMEN! Guy saying you will be killed doing this really gave me a chuckle. Seems like a lot are confusing barrel nut prefits and shouldered prefits too.
 
nksmfamjp said:
How many gunsmiths use a GO gage and shims and don't tell you about it as the buyer. It is within the gunsmiths responsibility to get it right. It is not a requirement to tell/teach the buyer how it was built.
Click to expand...
Let's say I didn't have the means to put together a prefit, so I took it to a smith to ensure the job was done properly. I interview the smith if they use gauges. If the smith wouldn't tell me or they said "no, I use a case and scotch tape," I'd be taking my rifle elsewhere. What would you do?

This is another reason I'm loath to buy "custom" rifles off the classifieds. I have no idea how the rifle was built.
 
MagnumManiac said:
This is the most overthunked thread I have ever seen on here.
A pre-fit for a PARTICULAR ACTION is a finished fitted product.
It requires no gunsmithing, it simply screws on and headspace and timing are done. Each barrel should be within SAAMI tolerances when CNC turned/threaded/chambered.
The only time you need go/no-go gauges is when you are cutting chambers.

Cheers.
Click to expand...
You said the magic words "should be". In 50 years as a gunsmith, I have seen enough AR barrels that were out of headspace to use as tent stakes. Never trust a manufacturer. The end user/installer should always verify unless you can guarantee the manufacturer NEVER makes a mistake.
 
Taj said:
You said the magic words "should be". In 50 years as a gunsmith, I have seen enough AR barrels that were out of headspace to use as tent stakes. Never trust a manufacturer. The end user/installer should always verify unless you can guarantee the manufacturer NEVER makes a mistake.
Click to expand...
Are these AR barrels a pre-fit to a PARTICULAR rifle, or are they a GENERAL barrel for AR's.
This is TOTALLY DIFFERENT to a pre-fit for ONE ACTION…

I've been gunsmithing a long time, pre-fits don't exist here, but I can machine numerous barrels, chamber them and fit them to ONE ACTION, MY OWN.

You are all confusing what a pre-fit is.

Cheers.
 

Similar threads

FrogFire7
Making a prefit "shouldered"
Replies
4
Views
1K
FrogFire7
FrogFire7
csmith86
Go/No Go Gauge Mystery
2
Replies
22
Views
5K
HRM Johnny
H
V
Belted go and no go gauges
Replies
10
Views
858
Victor3Ranger1
V
Okie Whitetail Hunter
6.5 PRC go/no go gauges
Replies
2
Views
2K
Okie Whitetail Hunter
Okie Whitetail Hunter
huntinherrrington
Action for shouldered switch barrels
3 4 5
Replies
63
Views
10K
Coors Man 264
Coors Man 264

Recent Posts

Top