"Muscle Brake" By Center Shot Rifles llc.
www.centershotrifles.com
VIDEO OF A 7MM DAKOTA AND 176 GRAIN BULLLETS
http://www.youtube.com/watch?v=RMit5FMqp6E&feature=player_embedded
The Muscle brake was designed specifically with the 90 degree first port, to shear the back blast away from the shooter. The concept of this brake was to protect specialty handgun shooters, from the severe concussion/blast effect of traditional angle ported brakes. The benefits of reduced concussion in conjunction with the angled ports will prove popular with magnum rifle enthusiasts as well.
There are a number of good brakes on the market today. Every one of them is designed for function on rifles. This brake is the first designed with short barreled attitude of protecting the shooter from the fierce back blast that is generated from magnum handgun cartridges.
These brakes are manufactured on state of the art CNC equipment to exacting tolerances. Shoulder, threads, OD and thru hole are CNC lathe turned in one set-up, minimizing run-out, and producing the most concentric product possible. You have the choice of thread tennons with these brakes. Pricing will remain the same for mix and match. All brakes are 416SS.
1/2 by 28 tpi, 5/8 by 24 tpi, 11/16 by 24 tpi.
Suggested retail………….$115.00 each
The Muscle brake is approximately 2" long, 1" tall from flat to flat, and 1.25" wide, ports are .250" wide and .800" tall. The thru hole must be lathe bored .020" over bullet diameter during installation. The rear end of the brake can be taper cut to meet barrel OD's under 1 inch.
Concept by Neal Cooper, Design by Jim See
Center Shot Rifles llc
2009
Coming soon; The New "Extreme Muscle Brake" will feature a 4 baffle design, with a diameter of 1.5 inches and a length of 2.5 inches. It will be round, and can be left that way for large barrels, or slabed off.
www.centershotrifles.com
VIDEO OF A 7MM DAKOTA AND 176 GRAIN BULLLETS
http://www.youtube.com/watch?v=RMit5FMqp6E&feature=player_embedded
The Muscle brake was designed specifically with the 90 degree first port, to shear the back blast away from the shooter. The concept of this brake was to protect specialty handgun shooters, from the severe concussion/blast effect of traditional angle ported brakes. The benefits of reduced concussion in conjunction with the angled ports will prove popular with magnum rifle enthusiasts as well.
There are a number of good brakes on the market today. Every one of them is designed for function on rifles. This brake is the first designed with short barreled attitude of protecting the shooter from the fierce back blast that is generated from magnum handgun cartridges.
These brakes are manufactured on state of the art CNC equipment to exacting tolerances. Shoulder, threads, OD and thru hole are CNC lathe turned in one set-up, minimizing run-out, and producing the most concentric product possible. You have the choice of thread tennons with these brakes. Pricing will remain the same for mix and match. All brakes are 416SS.
1/2 by 28 tpi, 5/8 by 24 tpi, 11/16 by 24 tpi.
Suggested retail………….$115.00 each
The Muscle brake is approximately 2" long, 1" tall from flat to flat, and 1.25" wide, ports are .250" wide and .800" tall. The thru hole must be lathe bored .020" over bullet diameter during installation. The rear end of the brake can be taper cut to meet barrel OD's under 1 inch.
Concept by Neal Cooper, Design by Jim See
Center Shot Rifles llc
2009
Coming soon; The New "Extreme Muscle Brake" will feature a 4 baffle design, with a diameter of 1.5 inches and a length of 2.5 inches. It will be round, and can be left that way for large barrels, or slabed off.
Last edited: