I,ve changed 3 scopes and rings on it . The one thats on it now is one that i took off my 338 Lapua Mag and i know that its good .
Poor accuracy , need help.
- Thread starter Sasman
- Start date
Help Support Long Range Hunting Forum
Do you have any muzzle attachments?
Yes . I shoot so much that i use muzzle brakes on all my rifles .
Have you tried switching out the brake?
Sdvldog1371
Member
I had a custom 300 PRC built that wouldn't shoot smaller than an inch and a half no matter what. I swapped out the scope, scope rings, loaded for it with converted 375 ruger brass. Then when ammo came out, factory ammo, then reloads, then ADG brass, Lapua etc... it just didn't like anything and the best i could do was about 1.5" at 100. The rifle was shoved in the back of my gun safe for years.
I purchased an MPA 300 PRC hybrid hunter and out of the gate it was a 3/4 moa rifle with factory ammo. This summer, while load developing for the MPA and preparing for hunting I stripped some parts from the old 300 PRC, scope, level, rings, bipod...all of the lighter weight parts. While reassembling the original rifle with the heavier parts, I went through and loctited and torqued everything and low and behold...the front screws of the scope rail were finger tight, no loctite, bedded scope rail, all work done by a highly regarded gunsmith.
I also have noted that my MPA shoots in the .5s and high .4s with a brake and eventhough it kicks like a mule, it shoots in the .2s for 3 shots, low .3s for 5 shots in a row...carbon wrapped barrel pushing 245s fast.
My long winded way of saying, check your scope rail, rings, then scope. Then check without a brake, make sure your scope rings are seated forward when torqued. Make sure your action is seated fully rearward when tightening. Tighten in increments, front to rear and make sure the front is fully tightened before the rear.
Lastly, if the rifle isn't adjustable and properly adjusted, you're likely the culprit. You have to be able to mount and drive the rifle repeatabley to know if it's truly the rifle system or you.
With all the years of experience I have, I relegated an expensive custom rifle to the life of a safe queen just because it never crossed my mind to check the scope rail...so stupid, so obvious and simple...but in all the scope swaps and other crap, I never checked the scope rail screws. Check the simple stuff.
Best of luck to you
I purchased an MPA 300 PRC hybrid hunter and out of the gate it was a 3/4 moa rifle with factory ammo. This summer, while load developing for the MPA and preparing for hunting I stripped some parts from the old 300 PRC, scope, level, rings, bipod...all of the lighter weight parts. While reassembling the original rifle with the heavier parts, I went through and loctited and torqued everything and low and behold...the front screws of the scope rail were finger tight, no loctite, bedded scope rail, all work done by a highly regarded gunsmith.
I also have noted that my MPA shoots in the .5s and high .4s with a brake and eventhough it kicks like a mule, it shoots in the .2s for 3 shots, low .3s for 5 shots in a row...carbon wrapped barrel pushing 245s fast.
My long winded way of saying, check your scope rail, rings, then scope. Then check without a brake, make sure your scope rings are seated forward when torqued. Make sure your action is seated fully rearward when tightening. Tighten in increments, front to rear and make sure the front is fully tightened before the rear.
Lastly, if the rifle isn't adjustable and properly adjusted, you're likely the culprit. You have to be able to mount and drive the rifle repeatabley to know if it's truly the rifle system or you.
With all the years of experience I have, I relegated an expensive custom rifle to the life of a safe queen just because it never crossed my mind to check the scope rail...so stupid, so obvious and simple...but in all the scope swaps and other crap, I never checked the scope rail screws. Check the simple stuff.
Best of luck to you
ShtrRdy
Well-Known Member
I've been having a similar problem to what you described. I've described it on another forum.
I've tried two different factory loaded ammunition that works well.
You might want to try some factory ammunition to see if there is some hope. I would suggest buying a box of Federal Gold Metal Match with the 168 gn SMK bullet AND a box with the 175 gr SMK bullet. Try shooting a group with these two. One of them will likely shoot well.
@Mram10us -- is there something you've experienced when using a brake?
OCW example and next step help
I am performing an Optimal Charge Weight load development as described in the Ryan @FURMAN video and am thinking some of the excellent knowledge on this forum could help me with my next step. The rifle is a Stiller action with a Krieger barrel and Trigger Tech mounted in a Legacy AICS...
www.longrangeonly.com
I've tried two different factory loaded ammunition that works well.
You might want to try some factory ammunition to see if there is some hope. I would suggest buying a box of Federal Gold Metal Match with the 168 gn SMK bullet AND a box with the 175 gr SMK bullet. Try shooting a group with these two. One of them will likely shoot well.
@Mram10us -- is there something you've experienced when using a brake?
Had a 338 edge that wasn't grouping. Switched from 3 to 4 port brake and touched up the crown. Shot great after.
Sdvldog1371
Member
MagnumManiac
Well-Known Member
Have you put the action back into the original stock and checked grouping with it?
Or, is this the original stock?
Bedding, trigger fitment, magazine fitment, scope base screws, bottom metal fitment and barrel channel fitment (free floated) can all cause issues singularly or as a combination.
Sounds to me like a simple issue that has been overlooked…
Cheers.
fyaman2
Member
Remove and and properly retorque all screws (Action, scope mount bases, rings, picitanny rail screws). Place nail polish/thread locker on them. After that id say bed your rifle. Check barrel clearance between the stock. If none of that works try a different ammo, scope and or shooter in that order. Its all about eliminating variables.
