PddPdd
Well-Known Member
I didn't read through all the responses but a key piece of information is, do you want to use the hides or just kill the coyote?
-
If you are being asked to change your password, and unsure how to do it, follow these instructions. Click here
Best AR15 Coyote cartridge?
- Thread starter DUCKMAN11
- Start date
Help Support Long Range Hunting Forum
snox801
Well-Known Member
Rl10x
Kill coyotes. Fur friendly is not a consideration
Then in my opinion the larger case cartridges are the most ideal. 6.5 Grendel, 6mm ARC, 22 ARC. More energy than the .223 Rem/5.56 case.
ewnanney
Active Member
25 DTI, basically 6.8 spc II necked down to 25cal. Pushes 90gr gamekings close to 3000fps/sub 1/2moa. Fireforming loads shoot nearly as good as formed brass. No broken bolts!
Grendel bolts make me nervous
https://bcprecisionballistics.com/, I was looking at this 6mm Max as an option. Good luck.
Mine had been good but valid point. Now you're making me think I should pick up a spare bolt.
TRG65
Well-Known Member
- Joined
- Dec 21, 2017
- Messages
- 462
I went with 6ARC. I don't have as much time as I'd like and I used a 108 ELD-M because that is what I had loaded last season. The fur damage was impressive. I started load work up for the Barnes 105 and also the 95LRX. I focused on Target, 540, and 4895 for powders. With the 105s, the velocity node is about 2550 and for the 95 it is about 2750.
I think if I was picking from scratch, I'd go with the 6mm Mongoose. Start with 223 brass and reform. The cartridge can still run 105s as long as you use metal mags, and the velocity is about 2500.
I think if I was picking from scratch, I'd go with the 6mm Mongoose. Start with 223 brass and reform. The cartridge can still run 105s as long as you use metal mags, and the velocity is about 2500.
The main reason that steers me away from the Grendel/ARC case is the low pressure ceiling. 5.56 runs at 62k and the ARC's run at 52-55k. There ain't enough meat on that bolt to turn the volume up.
I'd also likely run a 65gr vmax in an ARC. Sub 250yds and that extra BC is kinda wasted.
Mathewsboy, I run 21.5 grains of H335, giving me around 2900 F.P.S. M.V., C.O.L. is right at 2.200 the thing is the slower twist rate of 1:12 for the lighter bullet weight. Most of the newer barrels have a faster twist rate for heaver bullets. Stoner built the M-16 for a specific bullet weight of 55 grains and at first, he used a 1:14 twist rate in a 20-inch barrel, it was later slowed to a 1:12 twist rate. Recently the need for more knock-down power was realized, for military use, so bullet weight was increased but in order to stabilize the heaver weight bullets the twist rate was increased causing the lighter weight 55 grain bullets not to stabilize as well. They also tend to like 2900 F.P.S. M.V. out of my rifle they nearly always expend all of their energy in the coyote and on fox they sometimes have some copper fragments exit the far side. Yes, old school but it does what I want it to, so I am happy with it for now. Just what I have found to work for me, but it may not work the same for others.
lyle2231
Well-Known Member
White Oak Armament / John Hollinger took a 6.8 case necked down to 6mm. 6mmWOA . I shoot one and it is a good cartridge. Just run the 6.8 brass thru the sizing die, he sells them, prime, powder, seat bullet. 70-80 grain bullets work well.
HTH.
HTH.
