Weather & Elevation vs consistent load HELP

N

Nevrsummr

Well-Known Member
Joined
Dec 9, 2019
Messages
597
Location
Idaho idaho
I have a load worked up for a favorite rifle that is a fantastic load. I have shot the same exact load for 2 years in many weather conditions with great results. Hunting last weekend my wife shot a 1" group at 450yds with it just to confirm dope at that elevation
1000010777.jpg
. The next day hunting after 2 shots the 3rd shot was way hot 🔥. Blew the primer. Bad ejector marks. Stiff bolt. Pic attached.

My understanding is cold weather and high elevation should reduce a loads intensity, Is that wrong? I shot same load in 80* dry hot weather with no issues.

My wife said that the bolt was a little stiff on one of her previous shots as well.

Normal shooting elevation is 2500' and around 50-70*f. Hunting elevation was 7800 and 24*f

No I did not mistake a primer. Highly unlikely that it was a powder overthrow as I have tested the load and did not see pressure signs till 1gr higher. And I check each throw.
 
As to the actual question:

Elevation makes your shot go faster or simply increases MV. Air is less dense at altitude than being closer to sea level.

Cold makes air more dense. So it decreases MV.

So, here's the mind boggler that usually causes people to argue. Does MV directly correlate to pressure?

And if so, in your case, was there enough of a MV increase pressures to cause a such pressure signs…?
 
dfanonymous said:
As to the actual question:

Elevation makes your shot go faster or simply increases MV. Air is less dense at altitude than being closer to sea level.

Cold makes air more dense. So it decreases MV.

So, here's the mind boggler that usually causes people to argue. Does MV directly correlate to pressure?

And if so, in your case, was there enough of a MV increase pressures to cause a such pressure signs…?
Click to expand...
Shouldn't all the shooting world / geniuses already have an answer to this? I'm certain this isn't a new problem. Right?
 
308win said:
Carbon ring, they show up fast and screw up the while process. My proven load did the same thing this week. Went from 1.5" vertical at 140pyrds to a 21" vertical, just flat forgot to clean all the carbon out
Click to expand...
Working on cleaning now. Unfortunately a buddy borrowed my borescope
 
Just for my own information, do.we not have to make a distinction between down range velocity and muzzle velocity? The things they can alter muzzle velocity are pressure differences inside the chamber (temp sensitivity in powder, bullet jamb condition, carbon ring, etc). The things Density Altitude will affect ballistics (external to the barrel). So whatever if your load was tested at warmer temps, amd the charge didn't increase, then the issue is not related to elevation temperature, or humidity.

If cleaning the barrel.doesnt solve it, I would pull a couple bullets and check the charge. Also, I've seen excessive dampness from cleaning left in the chamber as well as a gun that got wet both al.ost lock up the bolt. If your charge was on the ragged edge, any moisture in the chamber could increase pressure significantly.

Definately keep.us posted on your findings.
 
The barrel could have got damp only from snow on the ground getting into it. Or humidity- say from warm truck to 20* cold outside. There was no precipitation. My wife was packing the rifle so I dont know for sure. It does have a muzzelbrake so that makes it harder to plug up a barrel. And 2-3 shots had just been fired previously to that. (W/ stiff bolt)

Say she did get some moisture in the barrel. A small amount from snow. How many shots does it take to clear that? Is it reasonable to think that 3 shots would be hot? The last one being hottest?

The gun hadn't been cleaned for a while.

Thanks for all your input & help here
 
Nevrsummr said:
I have a load worked up for a favorite rifle that is a fantastic load. I have shot the same exact load for 2 years in many weather conditions with great results. Hunting last weekend my wife shot a 1" group at 450yds with it just to confirm dope at that elevationView attachment 614257. The next day hunting after 2 shots the 3rd shot was way hot 🔥. Blew the primer. Bad ejector marks. Stiff bolt. Pic attached.

My understanding is cold weather and high elevation should reduce a loads intensity, Is that wrong? I shot same load in 80* dry hot weather with no issues.

My wife said that the bolt was a little stiff on one of her previous shots as well.

Normal shooting elevation is 2500' and around 50-70*f. Hunting elevation was 7800 and 24*f

No I did not mistake a primer. Highly unlikely that it was a powder overthrow as I have tested the load and did not see pressure signs till 1gr higher. And I check each throw.
Click to expand...
Could you have run into a "cold weld" situation?
 
I have popped primers when liquid/oil was present in my barrel.
I have ruptured a case when the neck clearance wasn't enough. Carbon ring will reduce clearance.
 

Similar threads

S
Most consistent factory brass? Help.
Replies
5
Views
1K
Greyfox
Greyfox
Welderboy11972
Quest for accurate/consistent reloads...HELP!!!
Replies
5
Views
831
Welderboy11972
Welderboy11972
M
Weatherby load help
Replies
2
Views
1K
MemorialRifle
M
D
Finding a load....Powder vs. Bullet.....Help Needed
Replies
8
Views
3K
SBruce
S
7
Varget vs Cold Weather
Replies
5
Views
4K
goodgrouper
G

Recent Posts

Top