• If you are being asked to change your password, and unsure how to do it, follow these instructions. Click here

Rem 700 Long actions can shoot almost any belt cartridge

duckklr said:
In other words you've neveractually tried it but speak only from what you've been told. You've never tried putting any of the above mentioned rounds in a standard Rem La action and running them through have you. Blah Blah RUM bull squirt. Do you hunt or just flap?
Click to expand...
The RUM action is relieved under the rear receiver ring as well as at the feed ramp.
 
MagnumManiac said:
The factory 338 Lapua is not a standard LA, it is the same as a RUM.

I have built many rifles on all of these actions, they are all different spec, just like a SA is different, including those built for WSM's & SAUM and those on 222 based cases.

Cheers.
Click to expand...
But the action lengths, action screws spacing and magazine length are the same as a regular long action.
 
Rusty85 said:
Most if not all detectable magazines have their own feed lips.
And I'll throw another 700 action cut in the mix. The factory 700 DBM actions have no feed lips.
Click to expand...
True, ADL and BDL are different than the DBM actions as far as the feed rails. I converted an ADL 7rm to BDL stock with BDL bottom metal, then changed to a Quickclip and finally to a factory DBM. It functions and feeds but not great. The feed rails need widened a bit.
 
So I have this 300 WM action sitting here and for the life of me I can't get my 300 RUM ammo to go into the mag...Maybe you can assist???
duckklr said:
There are only two Remington 700 action lengths, the "short" action will accept .17 Hornet and up to approximately .308 and the "long" action will accept for example 30-06 and up including belted magnum/longer case calibers with C.O.A.L.'s up to 3.600" including the .458 Lott. There is no need for a longer "super magnum" action.
The Remington 700 long-action and magazine-box will easily accept, feed, shoot and allow extraction of modern belted magnum cartridges with the bolt face sized for .532 rim diameter and with up to C.O.A.L. length of 3.600" without ANY modification other than a barrel change to the desired caliber/case.
A 30-06 or .270-chambered model 700 LA (for example) will accept three (Snap Cap) .375 H&H Magnum rounds into the magazine box and allow the bolt to pick up each round and chamber it as deep as the smaller chamber will allow without the smaller bolt-face extractor (.473") grabbing the rim. This demonstrates that the long action magazine box will handle the magnum cartridges and that the long bolt will pick up the cartridges. (This shows that a Rem 700 30-06 action and magazine is all ready to accept much longer cartridges.)
ALL Remington 700 LA bolts will swap actions, maybe not smoothly and the bolt faces may be for different rim diameters but they will swap!
My Rem 700 in chambered for 8mm Rem Mag will load three .375 H&H Mag Snap Cap rounds into the magazine box and the bolt will (again) pick up each case and push it into the chamber until the larger .375 aluminum bullet stops at the smaller chamber neck and the bolt extractor will engage the the rim properly if jammed home but will require a cleaning rod to force it back out. (Snap Cap rounds are made of aluminum and will not adversely affect the chamber, neck, or lands if contact is made.) I also shoot a Remington 700 chambered in .458 Win Mag and the action is identical to that of the 8mm Rem Mag (the bolts will swap).
The following belted cartridges meet the criteria of factory rim diameter of .532" or .5315" and a C.O.A.L. of 3.600" and are the offspring of the .375 H&H Magnum or one of its derivatives:

7mm Shooting Times Western
.300 H&H magnum
8mm Remington Magnum
.375 H&H Magnum
.400 H&H Magnum
.416 Remington Magnum
.458 Winchestern Magnum (3.340")
.458 Lott

The 8mm Mag and the 7mmSTW have the highest working pressures of 65K and the rest have working pressures of approx. 62K. The 7mmSTW case has the greatest sustained profile, much greater than that of its parent the 375 H&H.
Feel free to disagree but please, only if you have installed or attempted to install a 7mm STW, .375 H&H, or larger caliber belted cartridge barrel with no modifications, into a Remington Long action receiver and had it NOT load, fire and/or extract safely. There are frequently those who say it will not work without "grinding" this or "machining" that and have only B.S. and rumors to back up their erroneous claims, even from at least one major barrel maker.
Come and get me!
Click to expand...

So I have this Remington 300 WM sitting here and for the life of me I can't get my 300 RUM ammo to go past the feed rails and into the mag...Maybe you can assist???
 
This is just a standard Rem 700. No detachable magazine with any kind of lips, the action itself. Perhaps you're not familiar with original Rem actions and they haven't changed. Maybe what some folks refer to as "rails' help control the feed.
Just remember, Remington offered their standard long action in 8mm Rem Mag in 1978 with no modifications to the original action. And as I stated above, you can take a standard action rem700 in 30-06 and the builtin magazine box will accept three belted magnum cartridges ( calibers listed previously) and the bolt will pick each single cartridge and start it into the chamber. TRY IT!
I shoot several of these calibers in Africa every year with my favorite being the standard Remington long action (same as a 7mm Rem Mag or a 30-06 Springfield action) but in Winchester .458 Magnum.
I just don't get some of you, you've never tried it but you poopoo it!
 
Shane Lindsey said:
So I have this 300 WM action sitting here and for the life of me I can't get my 300 RUM ammo to go into the mag...Maybe you can assist???


So I have this Remington 300 WM sitting here and for the life of me I can't get my 300 RUM ammo to go past the feed rails and into the mag...Maybe you can assist???
Click to expand...
Is the action a Remington 700 long action? The non-belted RUM case diameter is .550 in diameter and the rim diameter is .534. I did not include this cartridge in my original post nor did I list the 470 Nitro Express or 50BMG did I!
 
🤔
 

Attachments

  • IMG_9114.gif
    IMG_9114.gif
    1.7 MB · Views: 25
Nimrodmar10 said:
But the action lengths, action screws spacing and magazine length are the same as a regular long actioNo it isn't sn't internally
Click to expand...

duckklr said:
In other words you've neveractually tried it but speak only from what you've been told. You've never tried putting any of the above mentioned rounds in a standard Rem La action and running them through have you. Blah Blah RUM bull squirt. Do you hunt or just flap?
Click to expand...
Before sprouting BS, I think you need to do some actual measuring of REM 700 actions. These ARE the sizes of feed rails on REM 700 LA.
Standard action size (.473" bolt) have feed rails that measure .540" wide at the rear and .595" at the front.
Magnum action (.532" bolt) has .540" at the rear and .625" at the front for the magnum size shell to feed CORRECTLY. Mag cut-out is .965", the magnum size box has no windows.
Don't tell me what I do and don't know, it's ALL in my notes from building these rifles.
RUM action is .560" at the rear and .640" at the front, mag box/action cut-out is .965" wide. RUM box has windows cut into it so the receiver bottom didn't require widening.
Just because YOU made the cartridges feed, snap caps only, does NOT make it correct.
Off to the ignore list for you…bye bye!
 
Last edited:
The 700 RUM action can run HS Precision DBM without any mods. For the two you mentioned, I am not sure. Maybe the 3.715, but I don't think the 3.850 would work without milling the rear of the mag cutout and the bolt stop.
 
Last edited:
Philward said:
True, ADL and BDL are different than the DBM actions as far as the feed rails. I converted an ADL 7rm to BDL stock with BDL bottom metal, then changed to a Quickclip and finally to a factory DBM. It functions and feeds but not great. The feed rails need widened a bit.
Click to expand...
I should add that the quickclip worked fine being a centerfeed design and made to work with bdl actions. The rem factory DBM is the one with the feed issues.
 

Similar threads

Akredneck
Rem 700 long action
2
Replies
14
Views
884
Akredneck
Akredneck
.28Nosler
Any places to shoot long range in Virginia?
2 3
Replies
37
Views
4K
Paul Spaulding
P
C
if you think you can shoot long range
Replies
1
Views
2K
bailey1474
B
T
Where can a visitor shoot long range around Vegas?
Replies
0
Views
1K
tedsalad
T
sealgair
Cartridge Choice for Long Action Rebarrel
2 3 4
Replies
55
Views
7K
Hoss50
Hoss50

Recent Posts

Top