• If you are being asked to change your password, and unsure how to do it, follow these instructions. Click here

Why are some cases tight and others loose?

B

bitbythebug

Well-Known Member
Joined
May 5, 2015
Messages
121
I have many rifles but my 28 Nosler has given me the most grief in reloading. I resize and prime every case. I then trim them to precise length. I then load a bullet and some cases are loose and some are tight to very tight chambering. I turned all the necks and that doesn't help. What can possibly be the matter. I am not a competition shooter and don't have competition dies but have shot and reloaded for over 50 years. What am I missing. The tight cases seem to have pressure issues which cause fluctuations in velocities, which make it hard to be consistently accurate. Need some positive help.
 
This problem is caused by a Classic issue amongst cases based on the 404 Jeffrey.
The shoulder resists being sized by 2 things, cases becoming hard take more effort and springback is insufficient, also, the web resists sizing and this also requires more effort. So, essentially some cases size ok due to their softer condition and others don't.
Annealing should cure this, but I do not recommend trying to size more, because the softer brass will be too small.
Steep shoulder angles also resist sizing…

Cheers.
 
MagnumManiac said:
This problem is caused by a Classic issue amongst cases based on the 404 Jeffrey.
The shoulder resists being sized by 2 things, cases becoming hard take more effort and springback is insufficient, also, the web resists sizing and this also requires more effort. So, essentially some cases size ok due to their softer condition and others don't.
Annealing should cure this, but I do not recommend trying to size more, because the softer brass will be too small.
Steep shoulder angles also resist sizing…

Cheers.
Click to expand...
Makes sense. I will try and anneal those cases and report back. Thanks
 
bitbythebug said:
You got me thinking so I watched some videos on annealing and they identified another problem that I'm having, neck splitting. So I think annealing will greatly help my problem. Thanks for your responses.
Click to expand...
Maybe you should get some new brass and pick up where you started having trouble.
 
bitbythebug said:
I have many rifles but my 28 Nosler has given me the most grief in reloading. I resize and prime every case. I then trim them to precise length. I then load a bullet and some cases are loose and some are tight to very tight chambering. I turned all the necks and that doesn't help. What can possibly be the matter. I am not a competition shooter and don't have competition dies but have shot and reloaded for over 50 years. What am I missing. The tight cases seem to have pressure issues which cause fluctuations in velocities, which make it hard to be consistently accurate. Need some positive help.
Click to expand...
Do you have headspace gauges to measure and compare the headspace (dimension between base of brass and a datum on the brass shoulder) between cases that fit fine and those that don't? This would probably be caused by excessive stretch in your brass around .2" above the brass base. I use a body sizing die to deal with this excessive stretch directly after annealing. It can be caused by the brass being loaded hot prior to firing some nominal loads to size the brass to your chamber. Too much pressure causes excessive case stretch and increased material thinning and diameter at the .2" datum. In my experience Nosler brass is prone to this issue. ADG brass is thicker and stronger and not as prone to this condition.
Hope that helps.
 

Similar threads

G
Die help- tight die/loose chamber?
2
Replies
19
Views
4K
Trickymissfit
T
C
Why belted cases
Replies
13
Views
3K
Canadian Bushman
C
B
Case too tight
2
Replies
22
Views
4K
elkaholic
elkaholic
6
When are primer pockets too loose?
Replies
8
Views
5K
6x6 elk
6
S
Need some help with tight neck brass
Replies
6
Views
2K
Catfish
C

Recent Posts

Top