Is powder touch sensitive?

topcat265 · Sep 8, 2024

My supertrickler is accurate to a kernel of gunpowder. To save time, when there is an overthrow (usually very small) I'll reach in the cup carefully and take out one kernel, reweigh the powder and if perfect, use the load.
My finger will touch other kernels of course.
My SD's and ES's are pretty good. Am I contaminating the kernels I touch, or is it irrelevant?
Any thoughts?
T

trout004 · Sep 8, 2024

topcat265 said:
My supertrickler is accurate to a kernel of gunpowder. To save time, when there is an overthrow (usually very small) I'll reach in the cup carefully and take out one kernel, reweigh the powder and if perfect, use the load.
My finger will touch other kernels of course.
My SD's and ES's are pretty good. Am I contaminating the kernels I touch, or is it irrelevant?
Any thoughts?
T

I will do this sometimes, but just use a pair of tweezers…

Phil Rizzo · Sep 8, 2024

A little chocolate frosting normally makes them easier to lift

memtb · Sep 8, 2024

Only if you just changed the oil in your truck……and didn't wash your hands.

That may have been a bit of an exaggeration…..but, not by much.
The effect that the minuscule amount of oil from your skin would be immeasurable! memtb

lancetkenyon · Sep 8, 2024

Same here, but I use tweezers. My fingers are too fat and calloused to grab a single kernel.

FEENIX · Sep 8, 2024

trout004 said:
I will do this sometimes, but just use a pair of tweezers…

This!

topcat265 · Sep 8, 2024

Thank you.
I will keep up the practice. And perhaps use the tweezers.
Much appreciated.
T

6.5x300 WBY · Sep 9, 2024

topcat265 said:
My supertrickler is accurate to a kernel of gunpowder. To save time, when there is an overthrow (usually very small) I'll reach in the cup carefully and take out one kernel, reweigh the powder and if perfect, use the load.
My finger will touch other kernels of course.
My SD's and ES's are pretty good. Am I contaminating the kernels I touch, or is it irrelevant?
Any thoughts?
T

I do that all the time too. Love my supertrickler

Varmint Hunter · Sep 9, 2024

I do that whenever there is an over-throw. Clean, dry fingers aren't going to affect a few kernels of graphited powder.

ARlife4me · Sep 9, 2024

probably oily (skin, not petroleum) and/or sweaty hands isn't good.

topcat265 · Sep 9, 2024

Fortunately, my hands are neither sweaty nor oily when I am reloading.
T

Chranah · Sep 9, 2024

I also use tweezers. I'm glad I'm in good company.

lancetkenyon · Sep 10, 2024

I set my ST for .02gr under target weight, with a .02+/- variable (depending on powder, half a grain variable +/-). So, I also keep a few kernels on the bench for that .04 underthrow...

Mike Matteson · Sep 10, 2024

Phil Rizzo said:
A little chocolate frosting normally makes them easier to lift

i don't think that what he was or is looking for.

Is powder touch sensitive?

topcat265

Well-Known Member

trout004

Well-Known Member

Phil Rizzo

Well-Known Member

memtb

Well-Known Member

lancetkenyon

Well-Known Member

FEENIX

Well-Known Member

topcat265

Well-Known Member

6.5x300 WBY

Well-Known Member

Varmint Hunter

Well-Known Member

ARlife4me

Well-Known Member

topcat265

Well-Known Member

Chranah

Active Member

lancetkenyon

Well-Known Member

Mike Matteson

Well-Known Member

Similar threads

Recent Posts