MARLIN 882 / 925 / 25 etc. Trigger mod. / job

top predator

Well-Known Member
Joined
Nov 17, 2008
Messages
273
Location
NORTHEAST PA.
Earlier this fall, my brother in law wanted to have his Marlin 882 .22 mag played with a little, so I figured I'd start with the trigger, doing the bic pen spring trick. I didn't want to go too low on the poundage as my nephew may be handling it too and I wanted to err on the side of safety. started off with an over 7lb pull, ended up with 3lb.
When working with any firearm, make sure it is unloaded. Chamber empty, no magazine.
First, what I call spring #1 and spring #2
MARLIN882TRIGGERJOB006-worded.jpg

MARLIN882TRIGGERJOB005-worded.jpg

I found out that spring #2 was not the one to mess with, as it didn't do much for trigger pull, and actually created slam fires (on an empty chamber) and actually increased creep when replaced. Spring #1 is the one to mess with, and I replaced this one with the bic pen spring. I clipped the spring coil 1/4 at a time to where I felt it was safe enough for a junior hunter to use, but light enough to be more effective than the stock trigger pull.
Taking the trigger group was easy, just unscrew the 2 slotted screws that hold everything together. Toward the back side of the trigger group there is a spring that sits in a hole (or pocket), make sure this spring (#2) doesn't go flying out when dismantling.
You can also trim the coils on spring #1, but I opted to go with the bic pen spring and keep the original as is.
MARLIN882TRIGGERJOB004-worded.jpg

Step 1. Make sure rifle is unloaded.
Step 2. Remove the bolt.
Step 3. Remove action barrel from stock.
Step 4. Trigger group disassembly:
a) remove mounting screw #1
b) remove saftey lever
c) remove trigger (don't lose spring #1)
d) remove spring #1 (it'll just fall out, not attached or retained by anything other than compression of the trigger and sear bodies)
e) remove mounting screw #2
f) slide the sear body down (don't lose spring #2)
g) remove spring #2 from the pocket / hole in the receiver
Step 4. Place everything neatly as you removed it so as not to confuse what goes where in the sequence. Even draw yourself a diagram or take a picture to make reassembly easier if you must.

Reassembly is in reverse order, make sure the springs seat correctly in either the spring #2 pocket or spring #1 flat against the trigger body and sear body. Don't overtighten the mounting srews as it'll pinch things up.
I also like to lightly sand the inside of the trigger housing / post, the mating surfaces of the sear / trigger body, and where the sear body meets the bolt. I also like to smoothen the sides of the trigger / sear bodies, and the slot where the sear body "pokes" through the receiver.
MARLIN882TRIGGERJOB003.jpg

Once the trigger group is back together, reassemble the receiver / barrel back to the stock. Insert the bolt. Work the action forceably; don't be shy, TRY to make it slam fire. It's a nice little safety test. Speaking of the safety, make sure it engages. Pull on the trigger with some might to make sure it holds. With some protective padding on a hard surface, "drop with care" the butt of the unloaded but cocked rifle from anywhere between 12 and 24 inches. With and without the safety on. Try working the action some more.

The whole process takes an hour or less and only costs the price of a bic pen. You can trim more coils off until the trigger feels just right, and operates in a safe fashion. There's no way of saying how many coils to go with as those cheap bic springs are just that - cheap springs. But 1/4 coil at a time will not get you too far ahead of yourself. Alittle trial and error is involved, have a few pens on hand.
Of course this modification doesn't take the place of a quality replacement adjustable trigger, but does improve the stock trigger of the Marlin 882, 925, 25, and similiar trigger groups not equipped with the Pro-Fire trigger.
 
Predator,
I have a marlin 25 mn. I have attempted this trigger mod. When I replaced spring 2 with the pen spring my trigger pull did not change. I proceeded to order a new sear and springs. I even placed a shim in spring 2(number 6 shotgun pellet)as suggested in another forum. The trigger pull did not change. As an experiment I removed spring 2 altogether. My trigger pull now feels significantly lighter(acceptable to shoot) however I know that spring two serves a purpose. I am not going to shoot without spring two but I cannot figure out where I am going wrong. I also lightly sanded the trigger housing. Any suggestions would be greatly appreciated. Thanks
 
Spring No. 2 if I remember right just forces the sear back up to catch the firing pen when the bolt is closed. Spring No. 1 is the one that would affect trigger pull weight. I tore a rifle down for my brother that looks similar. Been a while though. There is 2 things that control trigger pull weight. First is friction between the parts, Be it the side housing burrs rubbing and the sear surface its self. I have a set of what they call number 8000 Japanese stones. (Woodcraft out of Parkersburg WV) These stones are a set of 4 with small knife edge, round edge, 90 angle, 60 degree edge. they will polish metal to a mirror finish. Once you get all the burrs cleaned out of the housing and get the sear contacts polished all pressure is from the springs themselves. Then it gets to matching the right spring and getting it adjusted. Good Luck and stay Safe on your trigger work.
 
Thanks for the tutorial. I have a marlin 8800SQ. Nothing more than a m25 with a bull barrel. The trigger is HORRIBLE but I'll give it a whirl. Thanks.
 
Warning! This thread is more than 11 years ago old.
It's likely that no further discussion is required, in which case we recommend starting a new thread. If however you feel your response is required you can still do so.
Top