Recent content by Stiletto150

That brings me to another thought. The action is heating up and changing the torque on the front bolt. My guess is the torque is less.

I have an idea. Buy an infrared thermometer for $25 on Amazon or somewhere. I found tons of uses for cooking with it. Measure the same spot at the tenon of the barrel and the tip of the barrel. Before you shoot and then after your shot. That's if your barrel has metal on both sides to take a...

pending sale

Up for sale is a Manners EH4 RH Long action Stock MCS EH4 26 oz plus +6.5 oz for mini chassis. Midnight Elite Hunter Camo MCS-BDL Mini Chassis Proof Research Sendero barrel inlet 1" Pachmayer Decel Pad 1" Badger Rail Flush Cups Rotating (2 Left Side) and bottom rear List...

Since the powder measure is taken. I would love the Frankford powder trickler.

My understanding is with the extra case space. Since your case is over saami creates more velocity. Probably from dwell time before it hits the lands. Cheap insurance and to rule out. RCBS has check weights. Part #98993 or 98992 Not sure if your balance was ever corrected with the shot in the...

-That I don't know, have been pondering how to pay for a website that can be an upload point for everyone's videos and pictures. Maybe the a wildlife reality report. The real question is how to get the anti's to watch it and change their mind slowly. It's going to be a long process. As for the...

Just think about this. If we could shoot anything we could and did, we would not be close to what the wolves do. Wolves spend their entire life just looking for the next meal and making wolf babies. We did some heavy damage years ago(on the wolves) so we could flourish deer, elk, sheep, bison...

ADG Brass. https://atlasdg.com/product-category/brass-cartridge-cases/?filter_caliber=7mm 300WM from company has been in low 15 SD. Without any brass sorting. ( I don't have a digital scale or else I would).

I am not sure where the Hill Brothers got there info but I have seen very similar from a lot of different books. This shows temp can change your POI 2 MOA down and altitude can change .5 MOA up. I want to say from recollection these are based around the 308 cartridge. My guess is humidity had a...

My take. Environmental variables have a lot to do with. I also believe your front rest had something to do with it. Not sure if the media(sand, plastic) in the front rests were the same but I have had 1/4" (up or down)shifts using different front bags during load development. a stiff front rest...

Send it in. Have them check the chamber. I just checked 4 different brass. Remy 7Mag and 300 WM(Same parent case) Win, R-P, Fed and ADG Brass. ADG once fired .512. RP and Win 2x and 3x fired-.513" Fed 2x fired with second sizing just the neck .513" I have the LW die and it can be a pain to do...

The nick comes from a burr inside the chamber. When the chamber expands on initial firing. It makes the mark. Then the cartridge shrinks and you don't usually see a drag mark or feel it. This rifle could have other issues that would be checked by Remington. If the neck is too tight or any other...

Send it back to Remington. It's a burr that you can probably see if you flip the rifle over, open up the bottom metal. It's a burr from the reamer. Just had the same exact issue with my Ruger. They polished it up and checked headspace issues as well. They might spend a little more time on it...

**All loads are over Sammi COAL and probably book max***Work up your stuff. Didn't find the max load on this one because I was patterning near the node of 2860-2890 fps. Went up 76.8 and may go to 77. 300WM-Berger 210VLD's ADG Brass-new brass CCI 250 H1000 76.8 gns 2846 fps average CBO: 2.820"...