Recent content by AKGuide

Hello all, Figure I would pick your brains a little as I want to rebarrel my current setup to save some weight and also shoot the heavies. Currently it wears a 10” twist pac-nor and finishes at 1” at the muzzle 28” long. With bipod it is at 17lbs and will be going with a carbon six barrel but...

Those should work well also I’d recommend swift sciroccos they are 150 grainers but are bonded. I’ve had them give me consistent groups at book max length and run them right at 3000fps in a 24” barrel so 2925-2950 should be easily attained with the 22” barrel.

With the mod 7 box you are stuck loading short. What game you chasing and at what range are you comfortable shooting at?

It is the most accurate powder out of my 350 Rem Mag using 225 grain bullets. It meters like a dream too for being an extruded powder. First I’ve heard they discontinued it. Darn shame it works really well in my 224 Valkyrie as well using 80+ grain bullets. I was going to try it in my 6mm arc as...

So far I’ve only loaded 400 grain A-Frames and also 400 grain Hammers out of my 416-375 RUM. Just like the 416 Buff it is just a necked up 375 RUM case to accept 416 cal bullets. It started out as a 27” barrel but I cut it and recontoured it to save weight to 23”. My loads only lost 50fps from...

I should say the load data days.

Mike and I were the going heavy in the 454 days (be safe) these were the good old days. The 10mm data McNette and I will get you in the right area (we tested these loads). Just saying!!!

What was your oal seating to the second band? I didn’t catch that in the video. Ready to give these a try in my 26” 7twist McGowen barreled AR-15. It currently shoots 100TGK’s at 2725, but would like to give these a shot. All my mags are windowed so I can seat to 2.355” if need be. Reuben

For prolonged shooting of lead I use my 6” aftermarket barrel. I also test my stock barrel to see if they are not over pressure. Lead can be shot out of the factory barrel but you need to clean more frequently as it leads up way quicker and can cause pressure spikes.

If it’s for your 460 I wouldn’t be surprised if it’s their 340LFNGC. It’s their most accurate bullet they make for the big 45’s. I will switch to these once my supply of cast performance 360’s is done.

17FEB2021 34F, 99%H, 29.85inhg Virgin Starline 1.480", Rem 7 1/2, [email protected], 107 [email protected]" CBTO for 0.010" jump 2721avg, sd5; 0.85" w/ magneto attached 0.84" without but 1.2" low and 1.08" left This was my most consistent load in my AR it has a 26" McGowan 1:7" 0.089" gas port barrel...

My load in a stock barreled Rem 700 BDL that is bedded with a tweaked trigger and extended Wyatt's box is: Norma brass @ 2.025" CCI BR-2 IMR 7977 @ 66.0 grains HbN coated 168 VLD @ 2.915" for 0.050" jump 2940fps average with an SD of 9 This load holds 0.5 MOA, if I do my part, out to 750 yards...

Doubletap 200 grainers are a good bullet as well. If you roll your own the 200 grain WFNGC from beartooth bullets is the best bullet hands down for the 10mm. Get ready to wait a few months for your order though as they cast them to fill your order. Load either to 1200-1250fps with either...

I know the techs say the 225 sierras like 2000fps or more for impact velocities. So that keeps me at 300yds and in with my 350 Rem Mag. Looking forward to your results Reuben

Working on a load using the 85.5 Berger hybrid. I will post my finding when completed. Using CFE223 as my powder knowing it’s sensitive but never shoot in the summer so should be okay. Found pressure around 2840fps in my 24” Bison Armory Bbl just working on seating depth now to tighten...